20 Most Recent Minolta DiALTA DI2510F All-In-One Laser Printer - Page 2 Questions & Answers

Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

what code ? sir/mam what number? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Only Window 95 or XP. legacy Minolta machine now KonicaMinolta. try below Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Rear of the machine remove the back cover Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Did someone leave a trash can or boxes under the output trays? To solve this problem requires removal of the rear cover of the finisher. Then remove the elevation drive motor assemble. Be careful don't want the output trays to fall!!!!!! Then while placing them in their proper position re seat the drive assy. The top tray should be just below the orange rollers (If they are cleaned) you will see several actuators the trays has to just touch them. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

First check the right side cover where the image unit is located. Check the two latches that latch that door are not broken especially the rear one. Then get a paper clip and stick the clip in the small hole on the right side of the control panel it will touch a switch. The control panel with go thru some screens when you see the screen with copiers on it on the left side of the screen in the middle you will see a small "." when dot appears touch 3 button. then the machine will continue to the code screen. press the utility button should see a new button "Maintenance Mode" touch it then touch trouble reset. the machine will again go thru screens will see the "." again do nothing. should go Ready to Copy. If the code comes back do not reset you are messing with the Fuser the Hot part continue reset with out a technician looking at and or replacing it can catch on fire that would ruin a perfectly good day. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Electrical disconnect Draws #2 draw #3 draw #4 and Draw #5 all connections for each of those draws is in the rear middle cover. Also remove the job tray that the device where the paper comes out for faxes print etc. leave only draw one connected power off the machine turn back on after ten seconds. if the code is gone have a bad draw (s) if it comes back replace the main board if you can find one. The Di251 is legacy machine Minolta is now Konicaminolta. If the code did not come back your going to start connecting each draw back one at a time. Fig out which one(s) is causing the problem Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Self Help Product Support Konica Minolta Business Solutions Inc Try above web site for operation manual and drivers free. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

First ensure that the right side cover is closed correctly. Check that the two latches that are on the door are not broken especially the rear one. Then fine a paper clip. With the machine on look on the right side of the control panel you will find a small hole. Place the paper clip inside the hole. (Once that is done you can only use that paper clip ever again :) Copier tech humor!) Watch the screen you might see abort code that OK. When the screen come on that show the copiers look to the left of the screen in the middle a small "." will appears when it does press 3. Nothing is going to happen. Code will come back. Now press the Utility button you should now see a button marked maintenance mode. Press it then press trouble reset. Once again the machine will go though its normal warm up will see the "." do not do anything. Ready to Copy Should appear. If the code comes back do not reset the code your messing with the fuser (The Hot part). It can catch on fire (That would ruin a perfectly good day) so have a technician look at it. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Fax board memory on fax board or the Multi function board. To get o memory chip have to remove several board recommend qualified tech. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Main Motor failure. Try first removing the image unit and reseat it. Then check behind each paper draw for paper. Then you might have a bad main motor or the control board that controls the motor is bad. I would have a Konicminolta Tech look at it. Drum been replaced lately? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Might want to have the developer replaced and drum/cleaning blade normally done all together, then run the F8 procedure and make sure the counters are cleared Did you recently replace the drum and the developer if so did you clear the counters for the drum and developer. IF not then the copier thinks the new drum and new developer are old. Copier works on the counters that's how it know it got a new drum and developer. Get new develop and new drum and have it installed correctly, Counters are clear before the unit is yanked out of the machine, then you remove the image unit/drum unit replace the developer/drum and cleaning blade. (DO NOT USE A VACUUM CLEANER WHEN REPLACING THE DEVELOPER static electricity can destroy the sensor located below the developer unit. Then reinstall and RUN F8. Make sure the fax line and Ethernet cable is removed can't print anything until the F8 is run. Or you start over with new developer and new drum Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

The best driver s you mite find for the Di251 is 95 or xp Di251 series is legacy Minolta now konicminolta try their web site but doubt you will find it Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Clothes stuck where? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

And ABORT CODE !!!!!Check the scanner home position sensor (Located all the way in the back of to the left under the big glass have to remove the big glass mite just need to remove the dust) to the left check the BCR board Located right side just below the scanner section in the middle right side cover remove to see.and the MFB3 board (located under the scanner in the rear Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Manual by pass tray lift the by pass tray is the step looking thing on the right side of the copier. check to make sure there is nothing stuck inside there. IF ok then mite want a tech come out and look at it Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

legacy Minolta equipment best is 95 or xp. Try konicaminolta web site drivers are free. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Go to konicaminolta web site drivers are free but I believe Di2510 only goes to Windows XP Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

first ensure the right side is closed (Section that exposes the drum cartridge) and that the latches are not broken OK with machine on take a paper clip end stick in the tiny hole on the right side of the control panel (From then on you can only use that paper clip:):):) for this procedure (Copier Tech humor:)) The paper clip is going to touch a small switch which turns the to several screens if its say abort that is ok what you are looking for is going to be on left side of the screen in the middle a small purple dot when you see the dot press 3 that will activate trouble reset it will still code out with your c500 code but now go to utility mode see the new button Maintenance touch it you will see trouble reset touch that machine will go thru the entire cycle again you will see the small dot DO NOT touch let it go to "Ready to Copy" if not you have a problem with fusing unit the Hot part DO NOT CONTINUE TO RSET you can catch the machine on fire have a tech come out a look at it. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Ip address is determined by your network not the machine. You tell Copier what address you are going to giver her. (STATIC) or let the DHPC sever decide. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f