20 Most Recent Minolta Di3010f Printer Questions & Answers

Your network determines that! To load your IP address once you have it go 1. Admin Management 2.Admin Settings #2 3. Network Settings, 3. Network Settings #1 Basic Setting and then place IP address Gateway and Mask. RECOMMEND YOU USE static IP not DHCP which then the sever determines your copier IP Not good Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

First check the right side cover where the image unit is located. Check the two latches that latch the door ensure they are not broken, especially the rear one. Then get a paper clip and stick the clip in the small hole on the right side of the control panel it will touch a switch. The control panel will go thru some screens when you see the screen with the copiers on it on the left side of the screen in the middle you will see a small "." When the dot appears touch 3 button. Then the machine will continue to the code screen. Press the utility button you should see a new button "Maintenance Mode" touch it then touch trouble reset. The machine will again go thru screens will see the"." again do nothing. Should go ready to Copy. If the code comes back do not reset you are messing with the Fuser the Hot part continue reset without a technician looking at and or replacing it can catch on fire that would ruin a perfectly good day Try this site for parts Try this site for fuser Precision Roller Printer Toner Cartridges Parts and Supplies Office... Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Machine is waiting for certain house keeping chores inside the system. You mite turn off the machine. Then remove the toner bottle, then turn on the machine with the bottle out, when the copier asks for the toner install it properly. Second when is the last time developer and drum where replaced? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Look for the ozone filter the fan next to it is bad replace it. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Self Help Product Support Konica Minolta Business Solutions Inc try this Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

select job list. what error code? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Self Help Product Support Konica Minolta Business Solutions Inc try this updated driver are frree Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Manual Bypass tray. the paper tray on the side of the machine check for a jam if not have a tech from Konica Minolta come out and check it out there was a service technical bulletin issued in regards to that issue. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Press the utility button, then touch screen, meter count, then stop00 stop 01. Then admin input to change the password default is 00000000. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Remove the first draw and check to ensure no paper behind the draw SECOND REMOVE THE ACCESS PAPER FROM the draw the left side of the draw is not for storing extra paper the space is available for when the draw is set to 11x17 paper DO NOT STORE EXTRA PAPER THERE. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

You need to add the printer I.P address to the list of printers on p.c start>devices and printers>add printer>then follow prompts

The developer should have been replaced by the technician. the solution is simple...replace the drum and developer and you will have nice crisp prints and copies.

Go to cameras and scanner in control panel and select scanner.

Please check out my TIP on installing a network printer.

Change it back. Here is your manual. https://www.manualslib.com/manual/1001522/Konica-Minolta-Bizhub-Pro-1050.html?page=110#manual There is also a Service Manual available for it if you ever need it.

MINOLTA EP1050 GENERAL Service Manual download ...

Elektrotanya https://elektrotanya.com > minolta_ep1050_general.pdf Download MINOLTA EP1050 GENERAL service manual & repair info for electronics experts. ... MINOLTA EP-1080 CS-PRO A3-COPIER 1993 SM service manual. MINOLTA EP-1080 ... ..

Question edited into written English. Misfeed Error, or Timing Error. You need dealer service. This is a Professional Machine. The fuser only heats the toner to set it on the paper. It is nothing to do with jams.

Yes the Fuser unit that part that is very hot well one of the sensors has detected a very hot temp. get a tech out o look at and reset it Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f