20 Most Recent Minolta Dimage Scan Dual II Film Scanner - Page 9 Questions & Answers

FIRST, if this code comes back. Have a technician look at it DO NOT CONTINUE TO RESET the code!!!! AS this is for the Hot Part called the FUSER. It can catch on fire! And that will ruin a perfectly good day!!!! 1. Turn OFF the main power switch. 2. Turn main power switch ON while pressing the Utility/Counter key. 3. Touch [Trouble Reset]. 4. Check to make sure that [OK] is displayed and the it has been reset. 5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly. REPLACE the fuser if it come back then do this procedure again Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

what is the service code. WOW now that is OLD sorry just haven't hear or seen one in a while:) Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Open close the front door if the code comes back replace the print head which houses the LASER and or the main board is bad. If you can find one very old machine build bye Minolta before merging with Konica now Konicaminolta Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

reseat the image unit or have the image unit replaced normally done by replace the drum and developer Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

try this site Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the fuser unit Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

what do you mean bye panel did not move up or down? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

You dont reset you have to have the drum and developer replaced or codes will start appearing. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Replace the black drum and developer unit along with the magenta (P-7) and yellow (P-8) image units and Transfer belt (P-21) Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

http://onyxweb.mykonicaminolta.com/OneStopProductSupport?appMode=Public try this Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

See if you can find a printhead assy. The printhead houses the LASER which places the image on the drum. It a legacy Minolta (Now KonicaMinolta) machine, but you mite find one on the internet. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

You cant because there is a chip and once the chip said the image unit is done its done unless you reset the chip filling it will not do anything Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

What is the model number? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Did you change your router? try loading new drivers free at Konicaminolta Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Hi, It could be the transfer belt that is not cleaning properly, causing a ghost image.

First check the alignment front and rear of the finisher, check the finisher exit guide rollers if the paper is exiting properly, open both rear and the front cover and check the lower gears attach is the up/down drive belt. that lower gear one might be broken by the pin slot.

Description Intermittent C-0201 (C0201), C-0202 (C0202) and C-0203 (C0203)paper lift error codes. Solution PROBABLE CAUSES: 1.The trail edge paper guide (p/n A03U R756 00) may not be pressed against the paper. This will allow the paper to fall backwards and induce the error code. Instruct the end user to check the position of the trail edge paper guide whenever paper is loaded into the paper tray. 2. Coupling for the tray lift for Tray 1, Tray 2 or Tray 3 is obstructed or out of alignment causing the tray to not lift. Inspect the coupler in the back of the machine for paper preventing the pin from seating in the coupler. Check alignment when tray is inserted. If out of alignment try to adjust the drive to properly align.

May want to clean the mirrors under the big glass, you may also have a bad drum. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

You can shake it from side to side. It will break up the toner. Side to side only. Or the connection of the cartridge into the machine it may not reconize cartridge. And if it has a pull strip it will/g ?|ask