OKI MICROLINE 321 Turbo Matrix Printer - Answered Questions & Fixed issues

0helpful
1answer

I use the printer to

You do not say how the cards are fed. Are they tractor fed or by sheet feed. I suspect sheet fed and the platen roller has gone shiny. Source a can of platen cleaner to clean the platen roller. DO NOT use alcohol or a spirit based cleaner.
1/21/2018 1:18:57 PM • OKI MICROLINE... • Answered on Jan 21, 2018 • 67 views
0helpful
1answer

We just replaced UPS with

Agree with pcfixup.ca. Remember the software on a pc overrides the printers actual settings.
11/12/2017 10:06:24 PM • OKI MICROLINE... • Answered on Nov 12, 2017 • 57 views
0helpful
1answer

Oki microline 320 form feed

Am afraid the Power Surge (when the power came back on) has damaged the unit and there is no "Reset" to these printers. You would need to replace the control board but as its a power surge there is a reasonable chance that the power supply will have been damaged/weakened and this will lead to a shortened life span of the printer. I would throw it away and replace with new. sorry, ( I am not a salesman either)
7/26/2017 7:31:00 AM • OKI MICROLINE... • Answered on Jul 26, 2017 • 189 views
0helpful
1answer

OKI MICRO LINE 321 TURBO REAR FEED PROBLEM

Have you tried taking out the Platen Roller (big smooth one) and washing it??? Soapy water is fine as long as you rinse & wipe it down to get the soap off... Sometimes the platen rollers slip when dirty and they can cause similar jams.
10/27/2014 12:59:52 PM • OKI MICROLINE... • Answered on Oct 27, 2014 • 364 views
0helpful
1answer

Printer Throws Alarm, HSD, Prop error and Head Problems

Most likely, you need to lubricate the shaft the head moves on and clean the positioning tape (carefully, the marks on it can be dissolved). Unplug the printer while it's moving the head, so you can manually move the head around. Use light oil, such as used in sewing machines.
10/17/2014 4:00:37 PM • OKI MICROLINE... • Answered on Oct 17, 2014 • 292 views
0helpful
1answer

Printer prints one line, then alarm light comes on and stops printing.

Sir the printer is giving line because the cartiage or toner is not of good quality so it does not melt properly and produces line while the alarm comes and stop printing is due to the problem in charging cathode or gutter
6/3/2013 10:47:13 PM • OKI MICROLINE... • Answered on Jun 03, 2013 • 640 views
0helpful
1answer

Need to speed it up

This machine operates at one speed ... it is not like it has a transmission and you can shift from drive into over drive. There are a few things you can do, however.

You can remove the print driver and reinstall with a fresh copy ... go to www.oki.com/support to get the latest driver available for this printer, which works with your current operating system.

There are features in the driver which will let you make the machine appear faster ... print in draft mode for example ... Your printer may be in HI quality mode and you may select a lesser quality print for another. Since I am not intimately familiar with this particular printer, I can only suggest you go into the printer profile and examine the options you may find acceptable.

To locate the profile, open the control panel, open printer folder, find and open your printer and take a look around.

Thank you for your quesiton this morning @ FixYa.com
6/22/2011 11:46:22 AM • OKI MICROLINE... • Answered on Jun 22, 2011 • 56 views
0helpful
1answer

Alarm flashing goes to prop

This is a "spacing alarm". check that the printhead moves freely from left to right. If not, remove the ribbon and try it again. If it is moving freely then it should be ok, if not it will need most likely the space motor or the main board replaced. In some cases it is also possibly the white carriage cable that runs from your main board to the space motor. Hope this helps.
3/4/2011 1:39:01 AM • OKI MICROLINE... • Answered on Mar 04, 2011 • 380 views
0helpful
2answers

When we set the font it prints for about 2 pages ,

You didn't mention which document type or from which program you are trying to print but the commands for the printer are normally embedded invisibly in the document and sent to the printer to accomplish font changes, punctuation, etc.
We might have a better answer and a suggestion if you comment back to this thread with the name/version of the program that produced the document.
2/21/2011 4:48:20 PM • OKI MICROLINE... • Answered on Feb 21, 2011 • 254 views
0helpful
2answers

When it prints there is a line through the text

Sounds like the print head is at fault. The print head is actually a vertical line of small wires that move in and out to form the dots as the head moves across the page printing one row of characters at a time. One of the wires has failed. While it is possible that cleaning the print head with contact cleaner will resolve the problem, it might be time to replace the print head, or likely buy a used working replacement printer at less money than the cost to repair.
5/18/2016 5:42:47 PM • OKI MICROLINE... • Answered on May 18, 2016 • 387 views
0helpful
1answer

Oki 321 turbo in PPR emulation mode, does a form

Generally the form feed character is sent by your software. Try setting the page length in the printer setup to be the length of one label.
2/15/2010 9:12:48 PM • OKI MICROLINE... • Answered on Feb 15, 2010 • 614 views
0helpful
1answer

When I installed the printer it works properly but

Hi,

This types of problem comes due to printer hardware problem but i would like to suggest you that uninstall complete printer driver and reinstall it again after reboot your computer. If you face same issue with printer then you need to contact with hardware vendor or manufacturer.

Thanks
Sachidanand
8/17/2009 8:43:41 PM • OKI MICROLINE... • Answered on Aug 17, 2009 • 122 views
0helpful
1answer

How to get oki microline 391 turbo to work with windows 2003 server?

use the HP laserjet 4 or 4000 print driver. this is the most basic print driver and has played nicely with the older printers
12/17/2014 5:46:32 PM • OKI MICROLINE... • Answered on Dec 17, 2014 • 52 views
0helpful
1answer

How do I change the font style on my microline 320 turbo printer

I have this manual for you on page 37 for changing font. https://files.support.epson.com/pdf/fx890_/fx890_u1.pdf
5/14/2014 8:39:00 PM • OKI MICROLINE... • Answered on May 14, 2014 • 758 views
0helpful
1answer

Printer not getting power, no lights come on

have you checked the wall socket , try another wall socket , try another power cord ,and check if all is switched on
10/9/2013 2:39:25 PM • OKI MICROLINE... • Answered on Oct 09, 2013 • 197 views
0helpful
1answer

How can i download service manual

here is the user manual, is that the same as the service manual? http://www.primoit.co.uk/pdf/06E20B7E-AC7E-4E84-BA06-D1DD86563306.pdf
9/20/2012 4:26:30 AM • OKI MICROLINE... • Answered on Sep 20, 2012 • 108 views
0helpful
3answers

Oki mc561 when we moved the moving company dropped my OKI MC561, now an error code 990 appears, Would dropping the printer damage the board?

really have to ask that anything dropped can be damaged
7/29/2021 2:32:11 PM • OKI Office... • Answered 2 days ago • 50 views
0helpful
2answers

Como puedo corregir el error 990 de la impresora oki 330dn

RESET OKIDATA TONER DRUM 1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time. 2. Menu window will show "OKI USER" 3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button. 4. "Diagnostic Mode xx.xx.xx S-Mode is indicated. 5. Scroll to "NV-Ram initial" is indicated. Push ENTER. 6. Window shows "NV-Ram- Initial Table 1". 7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window. 8. Restart printer. All toner, drum, fuser and transfer figures return to 100\%.
2/1/2020 7:19:10 PM • OKI Office... • Answered on Feb 01, 2020 • 51 views
Not finding what you are looking for?
OKI MICROLINE 321 Turbo Matrix Printer Logo

35 questions posted

Ask a Question

Usually answered in minutes!

Top OKI Office Equipment & Supplies Experts

WTF Chuck.....
WTF Chuck.....

Level 3 Expert

388 Answers

Ekse

Level 3 Expert

13435 Answers

Alvin Barnabas
Alvin Barnabas

Level 2 Expert

136 Answers

Are you an OKI Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...