20 Most Recent OKI C5150n Led Printer - Page 3 Questions & Answers

Try check this out. http://my.okidata.com/pp-C5150n.nsf/openingdrivermenu?OpenFrameSet
Download the driver and follow the instructions on the site.

Hi dianabusk:
You have a bad K (Black) toner cartridge or the sensor is dirty,the sensors are located on the toner cartridge and in the machine where the toner cartridge seats. Try cleaning the sensors and/or replace the K (black) toner cartridge. The sensors are a silver color.

Hope this helps

You will need service soon/ the toner is running out.Wont hurt to keep useing it.

possible bad drum.

You can set the registration using the control panel in the front.

You need to replace the magenta drum. Just because there is life left; it's possible it is scratched. Also, take a cotton ball dip in alcohol and wipe the LED's off when the cover is open; those black things that are hanging down from the cover. Also, make sure your drums are installed in the proper spots (magenta in magenta slot). If the toner "rubs off" after it prints... then the fuser is defective.

Hi


This error comes up when the printer detects that the toner of particular color is missing. This indicated that the indicated color toner is missing from the printer(eg-- C = Cyan, Y = Yellow, M = Magenta, K = Black).

C5150 may face a toner sensor error after installing used sets of toner cartridges and sometimes even after installing new toner cartridges as well. This error can be bypassed. This can be disabled by following these steps---

1. Turn machine on while pushing and holding the (+/-), menu buttons at same time.
2. Menu window will show OKI USER.
3. Scroll to Engine Dialog Mode is indicated Push Enter button.
4. Diagnostic Mode xx xx xx S Mode is indicated.
5. ( = 2 ) . Press (- or +) button until “ENGINE - PARAMETER SET =2” is displayed.
6. Push Enter button.
7. TONER SENSOR - ENABLE is displayed.
8. Push Enter button.
9. Press (- / +) TONER SENSOR = DISABLE is displayed.
10. Press ON LINE CANCEL buttons at same time.
11. (*) is displayed.
12. Restart the Printer.

Daniel Scott

The drum and toner cartridge are two separate items. You need to replace the drum.

I had the same problem. I came across the 160 error after I moved drums around. My issue started with error code 161. which appears to be the Magenta drum. Moving it to other color locations gave me errors 160, 162, 163. 160, I assume, is the cyan cartridge, then 161 is the magenta, 162 is the yellow, and 163 is the black. In my case, the magenta was very dirty. I pulled it out, used an eraser from a #2 pencil to clean the contacts. Used the shopvac to clean toner power out of printer. Turned it back on and it worked.

Hi


Thanks for using FixYa. Error 160 is a Toner Sensor Error; this error is displayed when there is some error with the Yellow Toner Sensor. You’ll need to check the toner lock lever is in position or not and then restart the printer. After doing this if still the issue is not resolved then you’ll have to get the sensor replaced. Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

check possible paper stock on roller side also clean sensor free from dust. try to feed paper manually by turning roller and observe for any obstruction.

print the staus page from the printer and it will be listed on that.

select page setup by clicking on the printer icon.
then you will see a drop down with 'size letter 8.5X11'. click on the drop down and select 'legal 8.5x14'.
press OK and you are good to go

im not really sure what to do i had this problem before...

This tells me the one of the Pickers in the fuser is damaged and causeing this Jam , I would replace the fuser and chaces are this most likely will resolve your problem

Driver download link: Oki C5150n Printer Driver

Hi,


A temporary fix would be just open and close the handle and check that the white plastic is back down.

For a permanent fix replace the toner cartridge. Let us know if you need further clarification.
Thanks for contacting fixya.com