Top 20 Pioneer Premier DEH-P960MP CD Player Questions & Answers

Sometimes the mechanism is misplaced, just disassemble that mechanism and turn on radio without the secondary plate and wait until the motor to get to the final position when it turns off again, reassemble.

have the same problem just my back screen buttons working. dont know what to do =] will try using remote for now but cant change cd. should i try reset ?? or i should not =]

Hello
I've the installation manual for your Pioneer DEHP960MP with me, but it is in a different language, somewhat German I thinks. All the wiring digrams are it it. But I can't upload it to you. as this Fixiya site allows me to upload 50KB only, and the document is in adobe acrobat 9 format, and have about 300KB. If you are interseted, send me your email address through Fixya. I'll send you that file as an atachment. OK.

i have the same problem.... mine still paying but everytime i have to take off face if i want to switch it off.... cant change songs or cd either... it happened yesterday =[

You need a ribbon cable replacement to the faceplate at the very least.

It's my understanding that there is an ribbon cable that needs to be replaced - it's Pioneer CNP6498 flex cable (CN871 to CN1801) at pacparts.com. Price is less than $9.00, but shipping there is crippling to say the least ($11.50 - WTF??!?!?!)

IF you find that the detachable faceplate also does not work, there is an additional ribbon cable that needs to be replaced. Try "DEH-P960MP" on ebay and you can find a replacement for less than $30 shipped. I received mine in 2 days and had it up and running within 20 minutes. It solved the problem.

You need a ribbon cable replacement to the faceplate at the very least.

Look the replacement cable up on ebay under "DEH-P960MP" and you can find a replacement for less than $30 shipped. I received mine in 2 days and had it up and running within 20 minutes. It solved the problem.

IF you find that the upper face (with the OEL display) also does not work, it's my understanding that there is an additional ribbon cable that needs to be replaced - it's Pioneer CNP6498 flex cable (CN871 to CN1801) at pacparts.com. Price is less than $9.00, but shipping there is crippling to say the least ($11.50 - WTF??!?!?!)

you probably have a broken flexible cable that goes from the face to the main motherboard.

You need a ribbon cable replacement at the very least.

It's my understanding that there is a ribbon cable that needs to be replaced - it's Pioneer CNP6498 flex cable (CN871 to CN1801) at pacparts.com. Price is less than $9.00, but shipping there is crippling to say the least ($11.50 - WTF??!?!?!)

you probably have a bad switch. if you have a multimeter you can check the resistance of the switches. if one is reading less than a few megaohms, that is probably the bad switch.

have u connected RED YELLOW CABLES together???

make sure your 12volt constant is plugged in(yellow wire on stereo) and check the rest of your wiring. red(ignition power)

Most likely there is a bad capacitor in the black screen. You will have to test each capacitor to determine which one is faulty. You can purchase a capacitor tester fairly reasonable.

This is normally due to a sticky load/shuttle mechanism.
its not a simple part that can be replaced by the user.
Most times it can be cleaned - but required disassembly of the unit to do so.
Your local Car Electronics repair center (authorized by Pioneer of course) will be able to disassemble, clean and re-lubricate the shuttle for approximately $35.

For S&Gs - remove the radio and set it on your dash and try it. The angle of installation, or METHOD of improper installation can cause the body to twist, and the mechanism will bind up too. If it ejects normally without being installed - it's the installation - not the unit.

Thanks for using FixYa!!

There are 2 thin slots on either side of the radio allowing pioneer keys to slide in and unlock.
you can use small allen wrenches or pieces of copper wire as well. Smash it thin with a hammer.

Thanks for using FixYa - a good rating for answering your FREE question is appreciated.

I also had this problem and the solution was to change the data bus, or if you want, you can pull out a little the data bus.

Hi:

The change in the backgroung color of the OEL display is totally normal. This funtion lets the display works in two modes rather than only one to prevent OEL display damage, it is like a screen saver. I had the same model I bought

necesitas el cable auxiliar creo que es color rojo y el azul que va a un fusible con corriente abierta tienes que estar seguro de que tenga todos los fusibles que son como 3o 4.

buena suerte,,

pink is cell phone mute and orange is illumination or dimmer. both are not needed for proper operation just be sure to take them off good if you don't use them.

for the most boom out of your kenwood subs go with a nice ported mdf box with the correct air space for your subs. this will make a big difference over just throwing them in any old box. i prefer slot ported boxes over round ports for looks and sound.

Hit source button until you are in aux mode... then plug in your external music source to the front 'aux in' with 3.5mm line Jack cable. You should be able to play and control from y he external equip.

Sounds like the ignitionwire aint hooked up or turned ON...hehe...;)