20 Most Recent Rangemaster Classic 90 (Electric) Kitchen Range - Page 2 Questions & Answers

It looks to me that you have to install a fuse that is capeable of coping with that grill.all thebestKolbrun

You should find that if you hold the button down, it will click on minute by minute, then after about 5 seconds constant holding it advances in 15 or 30 minute steps. Just keep the button pressed in

common problem,it will most probably be the solenoid FF device fitted by the oven burner,these can be obtained from Gas On Spares on 0121-585-7799.the will need the model number and serial number.

the timer must be set for manual or it will not function,if need help phone Gas On Spares on 01215857799 for help or advise

the electric fan oven and the gas oven is not working on my range master classic 90. I need advise --many thanks.

Welcome to fixya

Hello

I have a solution for this

Press Ok, Accept or replay so we may get started

Your pre-solution is coming up shortly

PLEASE REPLY OR LEAVE COMMENT TO CONFIRM YOU RECEIVED THIS EMAIL

My name is Bruce

did you event suss this out, i have same problem..
thanks sam

press and hold the (+) and (-) untill u put in the corerect time. dont forget its a 24 hr clock.if u make a mistake or press the wrong button.turn off the power supply for a minute or two then start again.

Hi,
If your electric oven is not heating then you probably have a bad heating element in your oven. This is not that hard to fix yourself...
Check out this tip that I wrote about the Oven not heating problem..

Oven Problems Electric Oven is Heating Slowly or Poorly
http://www.fixya.com/support/r4511800-oven_problems_electric_oven_heating

heatman101

Asker's Testimonial " thanks i will have my husband look into that. " - 2gunsally

DO YOU HAVE GAS IN THE TANK, AND IS THIS A NEW STOVE, AND HOW OLD IS IT IF ITS NOT BRAND NEW, THE PILOT MAY BE OUT.

Here is the manual for a tecnika oven
http://docs.google.com/fileview?id=0B8VBVp0MQQl6ZWU0ZWNlM2UtMDIzNi00NzM5LWE2ZWYtZDFhOTQ1YzY4MjE1&hl=en

You should be able to lift the door, align the hinges into the slots.Then lower the door and allow the notched area of the hinge to fall into place. This may take a couple of tries to accomplish.

u first have to set the correct time of day. press and hold the (+) and (-) untill u put in the corerect time. dont forget its a 24 hr clock.if u make a mistake or press the wrong button.turn off the power supply for a minute or two then start again.

to enter the start time of your cooking, press and hold the button to the right of the bell symbol button (second on the left) and the + button at thee same time, untill your required 'cook time' shows, then press and hold the 3rd button to the left, ( the empty pot symbol) at the same time press (+) or (-) untill your required 'stop time' shows.
AUTO will show on the display. set the oven to the required temperature. when your cooking is finished the beeber will sound.
TURN THE OVEN KNOB TO 0 FIRST. then press the hand symbol button once to stop the beeb, press again to return to manual cooking.hope this helps!

I'm sure you must have had an answer by now, but just incase anyone else has the same issue. The ovens don't work unless the clock has been set (happens after a power cut). To set the clock you need to hold down the left-hand two buttons (underneath the clock) and at the same time press either the + or - button.

whilst the fan is running the heating element which is usually in parallel with it should heat.. This usually means a faulty element..

Not sure what the installers issue is. Anything can be done. If it is a cabinet issue...(not enough room), the cabinets can be altered and if needed, a small section added beside the appliance, (next to the door). If its a wiring issue...IE: your 220 hook-up is in the wrong place, it would require some easy re-wiring. If its a hood problem, that can be altered as well...depends on how much you want to spend to keep the misses happy! Good Luck! I hope you find this to be very helpful!

Hi. If this is a ALL electric cooker then you can do the job yourself. If partly gas then you MUST have it done by a ALL GAS qualified engineer.

Its a fairly easy job but you will have to unscrew several screws on on the underside of the front panel and also on the rear of the appliance.
If you would like assistance then please phone me on 01733 307019


regards
Aardvark repairs