Top 20
Whirlpool DU1010XTX Builtin Dishwasher - Page 6 Questions & Answers
Dimensions for whirlpool dishwasher du910pfgg1
The vast majority of undercounter dishwashers measure approximately 24 inches in width, 24 inches in depth and 35 inches in height with adjustable feet. This means that the rough opening in your cabinets must be 24- by 24- by 35-inch. The dishwasher itself may be somewhere around 23 5/8 by 23 5/8 by 34 inches
8/13/2018 12:24:29 AM •
Whirlpool...
•
433 views • 0 helpful votes
Whirlpool quiet partner II Can not select cycle or cancel. Is there a factory reset?
You should find a trouble shooting document behind the kick panel of your machine. Follow the steps.
My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination.
The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again.
I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
5/6/2018 7:27:37 PM •
Whirlpool...
•
802 views • 0 helpful votes
Replaced circuit board and fuse on whirlpool dishwasher and lights still flashing and won't do anything??
My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination.
The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again.
I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to! This may still be the problem after you replaced the control board.
6/9/2018 12:04:17 AM •
Whirlpool...
•
281 views • 0 helpful votes
My whirlpool gold start button won't start at all it gives me a (start ?) and won't turn on at all. I hope you can help.
Jen
There is a trouble shooting document behind the kick panel at the bottom of the machine. Follow the steps.
My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination.
The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again.
I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
4/7/2018 11:43:37 PM •
Whirlpool...
•
180 views • 0 helpful votes
Whirlpool dishwasher GU2800XTVQO delay lights won't stay off. Tried turning circuit breaker off for 30 min turned back on same thing. Started wash ran for awhile stopped when delay light came on.
There is a trouble shooting document behind the kick panel at the bottom of the machine. Follow the steps to determine which component is at fault, but it may be corrosion in the low voltage connector.
My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination.
The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again.
I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
3/25/2018 8:24:07 PM •
Whirlpool...
•
237 views • 0 helpful votes
Not finding what you are looking for?