Top 20 Fisher and Paykel DD24DCX6 Dishwasher Questions & Answers

Could be fresh water entering the top tub through the dual inlet valve. Try turning off the water supply and see if the problem continues.

Most likely the lid seal and/ or the detergent dispenser seal is leaky. Do not operate the dishwasher in this condition as the water can cause electrocution because the mains voltage comes up to the drawer front panel. Most likely it is the detergent dispenser seal. see this diagram. http://spares.bigwarehouse.com.au/images/files/18816_a21ebb5ac093d66472cef9bd1e8f3b12.pdf

Pausing - how long? The pause means the wash motor keeps halting as it is waiting for the water temperature to increase to the right wash selection. If the heater is sluggish then it will take longer to heat. Try a simple rinse cycle and see if there is any difference. (Rinse cycle will use cold water to complete)

If the cycle is complete and dishes are clean, then you need to worry. Try to pull the drain hose up a bit under the sink. Also buy a Finish dishwasher cleaning kit and run dishwasher as per instructions on the kit. That should clean any obsrtuctions in the drain side.

Unfortunately the buttons are an integral part of the Control Board. If it turns on just wont change cycle it could be that the controller is not sitting in place properly, otherwise you would have to get another controller.A couple of things to try:Make sure it is dry, some can be really sensitive.The opposite, Put a bit of water on the pad or lick your finger.Touch something metal like a tap with your other hand while you try.If you want instructions on checking the controller is in place let me know.

Need to clean the pump sump and the drain sump to make sure there is no debris left. Most likely a bone chip or seed inside the channel connecting the two sumps. Use a thin rigid wire to clean.

Please confirm if this quirk you mention has always been with the dishwasher or has it appeared after you replaced the controller on the upper drawer.

I am assuming this is happening with both drawers and therefore, is unlikely linked to the controller replacement. Although I am curious why you needed to replace the controller which I believe is very reliable in these double drawer models.

Coming back to the drying fan, the manual is very clear that in spite of how much the remaining time on the drying fan operation is, it will turn off once you open the drawer. Is the behaviour any different when you enable the Auto power setting?

By the way I believe the dishwasher is already on enhanced dry mode unless the ECO button is selected. See bottom of page 7 in user manual.

Question edited for a lot more clarity. Your 'Possess F&K DW60FC' does not exist! :>D Question moved from Televisions category. Rebooting is not the fix, it won't work until you fix the pumping out. Fisher and Paykel dishwasher error codes f30 The F30 error code signifies that the flood switch on your machine has been activated. This indicates a problem with water drainage. This could be a one-off issue, or it could be a symptom of something deeper. For example, if the drain hose is bent or blocked, it could cause dishwasher problems like flooding.

How to Fix F30 Error on Fisher and Paykel Dishwasher

https://unitappliances.com.au > how-to-fix-f30-error-on-... Search for: Fisher and Paykel dishwasher error codes f30

Parts FYI.... https://spares.bigwarehouse.com.au/index.php?cPath=64658_64876_94119 Best to you

If your Fisher Paykel DD60 dishwasher is beeping when it needs to drain, it may be experiencing a drainage issue. Here are some steps you can try to diagnose and fix the problem:

1. Check for Blockages: Make sure that there are no blockages in the drainage hose or filter. A blocked drainage hose or filter can prevent the dishwasher from draining properly, which can trigger the beeping sound. Remove any blockages that you find.
2. Check the Drain Pump: The drain pump may be faulty, which can prevent the dishwasher from draining properly. Check the pump to ensure that it is functioning correctly. If the pump is not working, it may need to be replaced.
3. Check the Drain Valve: The drain valve may be faulty, which can prevent the dishwasher from draining properly. Check the valve to ensure that it is functioning correctly. If the valve is not working, it may need to be replaced.
4. Check the Control Board: The control board is the brain of the dishwasher and controls all the functions. If it is faulty, it can cause the dishwasher to not operate correctly. Try resetting the control board or replacing it if it is faulty.
5. Check the Sensor: The sensor may be faulty, which can cause the dishwasher to beep when it needs to drain. Try cleaning the sensor or replacing it if it is faulty.

If none of the above steps work, it may be best to contact a professional technician for further diagnosis and repair. They can inspect the dishwasher thoroughly and ensure that it is working correctly and safely.

Flood Pan alert

Troubleshooting an F1 Error in a Fisher & Paykel Dishwasher

https://www.hunker.com > ... > Dishwashers The F1 fault code indicates that water has filled the flood pan beneath the bottom drawer of the machine. This can happen if the drawer isn't shut all the way, ...

About the F4 error code on the Fisher and Paykel DD60DDFX9 dishwasher: The F4 error code on your DD60DDFX9 dishwasher indicates a fault with the heating element or the temperature sensor. When the dishwasher encounters a heating fault, it is unable to heat the water to the correct temperature required for the wash and rinse cycles. This can result in poor cleaning performance and may also affect the dishwasher's ability to sanitize the dishes. To troubleshoot the F4 error code, you can try the following:

1. Check the heating element: Use a multimeter to test the heating element for continuity. If the heating element is faulty, it will need to be replaced.
2. Check the temperature sensor: Test the temperature sensor using a multimeter. The sensor should show a resistance value of between 10,000 and 12,000 ohms at room temperature. If the resistance value is outside of this range, the sensor may need to be replaced.
3. Check the wiring and connections: Inspect the wiring and connections between the heating element and the control board. Make sure all connections are secure and free of damage or corrosion.
4. Check the control board: If the heating element and temperature sensor are both working properly, the issue may be with the control board. A certified repair technician will need to diagnose and replace the control board if necessary.

If there is no light or display on the LCD and the buttons are not functioning on your washing machine, and you have verified that there is power to the motor controller module and the wash controller module, it is possible that the issue is with the LCD or the ribbon cable that connects the LCD to the control board. To narrow down the location of the fault, you can try the following steps:

1. Check the ribbon cable: Inspect the ribbon cable for any visible damage or loose connections. You can also try gently wiggling the cable to see if this affects the display.
2. Check the control board: The control board is responsible for controlling the various functions of the washing machine, including the LCD. If the control board is faulty, it can cause issues with the LCD.
3. Check the LCD: The LCD itself may be faulty and not functioning properly.

If you are unable to diagnose and fix the problem on your own, it is recommended to have a mechanic or appliance repair technician take a look at the washing machine. They will have the necessary tools and expertise to properly diagnose and repair the issue.

Question edited for clarity, abbreviations don't work here. Question moved from Television and Video category. you will probably need a service call out. Control board issues?

DD24DI7 - Fisher & Paykel Product Help

https://producthelp.fisherpaykel.com > Integrated_Double Dec 11, 2017 - Installation Guide DD24DI7 (Integrated Models - External Ventilation Kit - Framed) ... Closed Drawer autolock using the remote control ...

Your remote control - Fisher & Paykel Product Help

https://producthelp.fisherpaykel.com > Clean > DD24DI7 Feb 18, 2018 - Your remote control · A single flash indicates a successful signal to the dishwasher. · Multiple flashes indicate that the dishwasher cannot read ... https://www.google.com/search?q=Fisher+%26+Paykel+model+DD24DI7+only+works+with+remote ..

https://www.manualslib.com/manual/575481/Fisher-And-Paykel-Dishdrawer-Dd603.html?page=22#manual this link takes you to the service manual for your machine, there will be details on manually testing individual components, you should be able to operate the pump and check that it is performing as it should, page 39 describes the process to lift out the rotor, do that and check the rotor impeller, this is the drain pump, if the rotor vanes are broken you will need to replace it,

Question edited for clarity and the addition of 'Dishwasher'. Check out the video in the link https://www.google.com/search?q=Fisher+and+Paykel+Dishwasher%2C+the+top+drawer+power+light+turns+on+and+off Please always include 'make model (what it is)' in all questions. Thanks. ..

Hi Brendan,The dishwasher will stop mid cycle if the door is not closed properly, please ensure that the door is shut firmly and the latch engages fully.Also a broken door latch, faulty control panel or failed electronic control board could be causing the problem.Hope this helps.Best,Dan

F1 Flood should have triggered. There is a small, 2 post sensor located under the cover and parts assembly (to the right hand side) of the Mains board (under the plastic cover in the left, lower, rear portion of the base - under the bottom drawer - #10 & 19 in the drawing) and this should trigger with a very small amount of water in the base pan. Maybe dirty, bent or disconnected sensor?? Otherwise, likely a bad comms harness or control board. This is very unusual - never encountered it in 20 years of F&P service. I personally have two of them. One of our kids have it too. We love the F&P dishdrawers.Note: to actually get correct parts you MUST have the full model and product codes.

usually they are hiding in plain site. Most seem to require tools to remove and are in the back so they are harder to get at. It is a conspiracy to sell more dishwashers.