20 Most Recent Technics SA-DX930 Receiver Questions & Answers


Fuse locations on Technics SA-DX930


I have got a service manual for you which will help you out.Please CLICK HERE

9/28/2017 11:52:05 AM • Technics... • Answered on Sep 28, 2017

RIAA preamp

Just plug the turntable into your phone inputs. If there is next to no volume then you need a preamp because you have a magnetic (low output) cartridge. If you have a piezo type cartridge the output should be enough to drive the amplifier to rated output. Of your unit does not have a phono input I can tell you that it definitely does not have a preamp built in.
4/21/2014 3:48:35 AM • Technics... • Answered on Apr 21, 2014

Digital input glitch, switches randomly from analog to digital.

what connections do you use for the device you are listening to, and what device are you listening to when this happens. you should use either an analog, or a digital connection to a device, but not both
3/8/2013 8:27:11 PM • Technics... • Answered on Mar 08, 2013

How can i get a owners manual for my technics

Here ya go:

Please rate my response if it was helpful.
8/1/2011 6:16:30 PM • Technics... • Answered on Aug 01, 2011

I moved and cannot find

The Technics SA-DX940 is made by Panasonic. The manua as a PDF is available here: http://service.us.panasonic.com/OPERMANPDF/SADX940.PDF . The directions for connecting the speakers start on page 14. The connection to the TV is on page 10. To use the SA-DX940 as just external speakers for your TV, connect either the digital audio out from the TV (if it has one) or the RCA audio out from the TV to the matching TV audio in on the SA-DX940.

I hope this helps.

Cindy Wells
6/30/2011 1:35:17 AM • Technics... • Answered on Jun 30, 2011

Unit turns on but has no output

Have you looked at the manual and understood every setting that could silence it?


Turn the volume control to something medium.

The errant switch, control or condition may change and you will suddenly release the amp's full power and possibly destroying your speakers. If a signal isn't audible at 1/2 volume it's probably not there.

Carefully examine the front panel for clues like a misplaced Mute or Tape Monitor control or Multichannel Analog Input selected.

There is a good chance that a common control may have developed a high-resistance or 'dead' spot through defect or idleness and is causing your symptom. Turn the POWER OFF and operate every control throughout its range a number of times, especially rarely-used ones like Tape Monitors and the Mute control.

Turn the volume to something reasonable and see if that helped.
6/11/2011 8:59:19 PM • Technics... • Answered on Jun 11, 2011

I have a Technics model.

Depending on the "overloading sensor" you may get an overload alarm from:
Too much input audio signal,
Distorted input audio signal,
Low power supply voltage (lower that the nomimal),
Changes at the internal dc power supply (due to high consumption at high audio levels)
and many many more....
At these high audio levels (you mentioned for 3/4 full power, your amp has a nominal 100W/8? per channel) I don't think that these kind of problems are easy noticeable, unless you use your amplifier for something like PA System. Anyway if you can give me more details (including audio source you use, number of speakers e.t.c.) about your problem I'll try to guide you eliminate (as much as possible) this problem.

In case of a problem or clarification or further details needed, don't hesitate to post me a reply before rejecting my answer.
If you are satisfied, accept my solution.

Thanks and regards
direct fixya link: http://www.fixya.com/users/technical114
6/1/2011 3:04:47 AM • Technics... • Answered on Jun 01, 2011

How do i hook up

Connect the Technics front Left and Right speaker out to the Optimus Left / Right IN. And what ever speakers you were connecting to the Technics front Left and Right connect it to the Optmus Left / Right Out. This is called a loop through connection. Just make sure the Amplifier red is connected to the sub woofer red and the Amplifier black is connected to sub woofer black - i.e No mixup on the colors.
4/29/2011 10:33:35 PM • Technics... • Answered on Apr 29, 2011

Right speaker does not work on both A and B

Before doing anything else swap the speaker connections over to make sure that the problem is in the amp and not the speaker / speaker cable.
If that doesn't solve it then it is most likely an internal fuse blown on the amplifier circuit board - they are little tiny glass ones, obtainable from most tv repair shops, but it is important to get the right power rating. Also some of these fuses are 'quick blow' (go instantly there is a fault) others are 'slow' or 'time' blow - take a second or two before they actually blow - make sure you get the right one (timed usually have the letter T next to the power rating)
3/23/2011 8:03:34 AM • Technics... • Answered on Mar 23, 2011

Technics Sa-dx930 receiver. Suddenly sound stopped,came

yes' - there are two fuses that are on the circuit board. remove the unit case and locate the fuses -- they will be near the internal amplifier. if it turns out that the fuses are good - then the problem could be the volume resistor plates or a bad amplifier. it might be worth taking the unit into your local stereo repair shop and have them take a look at it,, it could just be a bad resistor or diode on the circuit board and that is very cheap to fix.

2/13/2011 6:37:22 AM • Technics... • Answered on Feb 13, 2011

What is the model no. original remote control for

Dear Sir,
The original remote control model number for your equipment is
EUR647132. But this item is no longer available.You can find a substitute which will work effectively for your equipment(having the same features) are: EUR646489 and EUR646496 These remote can be purchased from panasonic.newremotecontrol.com I think this may solve your problem.
Regards, Chandrachur
11/9/2010 9:29:32 PM • Technics... • Answered on Nov 09, 2010

I have a technics sa-dx930 receiver and want to

It would help to know some details about tour TV - like its make and model. Or do you mean the CABLE BOX?

And there are TWO signals to consider - audio and video. WHICH is the one you need to hook up without involving the dvd/vcr?

Let's start with basics:

1) TV's are not audio sources. They are end-units for video and its medium-fi audio.

A TV's internal audio capacity is more a convenience for stand-alone listening than a serious approach at hi-end audio. Many of us have monitors with NO audio capability.

TV-related audio and video are best VIEWED via direct video connection to the TV; and HEARD through direct digital audio connection to the receiver.

2) The one NECESSARY connection you need from the receiver to the TV is the basic VIDEO that let's the receiver communicate with you through the TV.
6/6/2010 7:26:23 PM • Technics... • Answered on Jun 06, 2010

We had a power outage. Now it will not power up no

Take it to a shop and have them check it for burnt components.
5/28/2010 10:17:00 AM • Technics... • Answered on May 28, 2010

No consigo el ventilador de enfriamiento ahi

si te encuentras en Mexico ve a steren y si estas en USA ve a radio shack
4/12/2010 5:40:28 PM • Technics... • Answered on Apr 12, 2010
Not finding what you are looking for?
Technics SA-DX930 Receiver Logo

58 questions posted

Ask a Question

Usually answered in minutes!

Top Technics Audio Players & Recorders Experts

Morne Olivier
Morne Olivier

Level 2 Expert

265 Answers

The Knight
The Knight

Level 3 Expert

76851 Answers


Level 3 Expert

3290 Answers

Are you a Technics Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Technics Audio Players & Recorders

  • Technics Audio Players & Recorders

Most Popular Question

riaa preamp

  • Audio Players & Recorders