Radio Shack Wireless IndoorOutdoor Thermometer System - Answered Questions & Fixed issues


Sensor has gone bad if new batteries, taking it inside (if freezing cold out) and a reset didn't fix it.
LL.L means temperature is below range, i.e. no signal from sensor.

Radio Shack... | Answered on Sep 16, 2019 | 3,641 views


HHH means the temp is over the range that was designed. Where did you locate the sending unit?

Radio Shack... | Answered on Mar 14, 2013 | 505 views


When on channel one,hook up an oscilloscope to the channel output circuit on the output terminals.First read channel 1,then channel 2,then channel 3.You can leave the oscilloscope hooked up the whole time.Start on the highest available scale,then work your way down scale by scale until it is accurately readable.Then you will need to find the input to the counting circuit,most likely from a thermistor.You will need to reconfigure the counting circuit to send a signal from what the thermistor is reading for the temperature to 600Hz instead of what the current counting circuit is set at.You can achieve that by connecting the oscilloscope to the output side of the IC for the counting circuit with one lead on the output,one lead on the input,and determine what it is set at currently,then redesign it to pulse at 600Hz input which is 10 second intervals.Greg

Radio Shack... | Answered on Oct 30, 2010 | 258 views


how do you adjust the weather forecaster 63-1090 clock

Radio Shack... | Answered on Dec 31, 2012 | 1,134 views


The manual is available here: http://phone.manualsonline.com/manuals/mfg/radio_shack/58_ghz_expandable_cordless_telephone_with_talking_caller_id_digital_answering_system.html . Click on the Get this Manual button.

I hope this helps.

Cindy Wells

Radio Shack... | Answered on Jun 27, 2011 | 121 views


ask your phone company

Measuring Tools... | Answered 2 days ago | 13 views


What is 'rapair'?

Measuring Tools... | Answered 2 days ago | 12 views


It is a known issue

Try first a general reset:
- remove the batteries from the clock (thus turning it Off.)
- remove the batteries from the outside sensor (if you are not aware that it has batteries, then perhaps it is not working because the batteries are no good any more! check that also.)
- wait 10 minutes with no power to the device.
- put batteries back in, power On again.
- hit Reset.
- hit Receive button.
- change the channel for reception from the outside sensor.
- change the channel on the outside sensor to match that channel.
- then set the time once more, once the remote temperature is sensed once again.

If this does not get the outside temperature reading working again, you may have to replace that temperature sensor.

https://www.google.com/search?q=Model+spc373

..

Measuring Tools... | Answered on Jan 02, 2021 | 14 views


It is a wired system (outside unit to the indoor phone) and only available in South Africa. This seems to be the distributor and there is no manual online. The are far better systems with colour video, audio and wifi or bluetooth.

https://www.game.co.za/game-za/en/All-Game-Categories/DIY-%26-Auto/Home-Security/Intercoms-%26-Alarms/Alarms-%26-Sensors/Digitech-Wired-Door-Phone-BPSDP3206A/p/504101-EA

..

Measuring Tools... | Answered on Dec 30, 2020 | 19 views


Try removing all batteries, then reinstalling in the outdoor unit and waiting for it to start sending data before reinstalling batteries in the indoor unit. If you don't see data displayed on the indoor unit, the outdoor unit may have failed.

Measuring Tools... | Answered on Dec 24, 2020 | 15 views


5505E MEASUREMETER BATTERY CHANGE (3V CR-2032)
REMOVE WHEEL AND SHAFT BY GENTLY PULLING AXLE OUT OF UNIT.
DRILL OUT 7 PLASTIC HEADS WITH 3/16 DRILL BIT. (ABOUT 1\8 DEPTH)
SPLIT TWO SIDES OF CASE AND REMOVE HANDLE.
SLIDE OUT CLEAR PLASTIC CONTROL UNIT. PUSH DOWN ON BUTTONS AS YOU REMOVE SO AS NOT TO DAMAGE THEM.
PUSH DOWN SLIGHTLY TOWARD THE CASE ON LOCK TABS WHILE GENTLY PULLING CASE APART. START ON ONE END AND WORK YOUR WAY TO OTHER END. KEEP GASKET INTACT. OPEN CASE.
THERE IS A "Y" SHAPED RETAINER HOLDING IN THE BATTERY. WITH NEEDLE NOSE PLIERS, CAREFULLY SLIGHTLY SQUEEZE THE BOTTOM OF THE "Y" AND PULL UP GENTLY. YOU CAN NOW REMOVE THE BATTERY AND INSTALL THE NEW ONE. PUSH RETAINER DOWN TO LOCK BACK IN.
MAKE SURE GASKET IS IN PLACE AND PUT CASE BACK TOGETHER, MAKING SURE WHEEL ADAPTER IS IN PROPER PLACE. TURN ON AND TEST CONTROL UNIT AND TURN WHEEL ADAPTER TO MAKE SURE UNIT IS WORKING PROPERLY.
SLIDE CONTROL UNIT BACK IN BEING CAREFUL OF THE BUTTONS. RE-ASSEMBLE HANDLE AND PUT THE TWO SIDES OF THE CASE TOGETHER. I USED THREE PIECES OF ELECTRICAL TAPE TO HOLD CASE TOGETHER. ONE ON THE TOP BETWEEN THE TWO HOLES, ONE ON THE BOTTOM JUST ABOVE THE DISPLAY, AND ONE IN THE MIDDLE.
PUT THE PLASTIC PIECE IN THE HOLE AND LINE UP. MAKE SURE BOTH O-RINGS ARE ON THE AXLE SHAFT. GENTLY INSERT AXLE ALL THE WAY IN WHILE ROTATING IF NECESSARY.
I WAS SO HAPPY I HAD IT ALL BACK TOGETHER AND WORKING, I HADN'T TAKEN ANY PICTURES AND I DIDN'T FEEL LIKE TAKING IT ALL APART AGAIN. MIGHT ADD PICTURES LATER IF NEEDED. I HAD BEEN LOOKING FOR YEARS ON HOW TO CHANGE THE BATTERY, AND I FINALLY MADE UP MY MIND THAT I WAS GOING TO DO IT.
JMS 10-20-2020

Measuring Tools... | Answered on Oct 21, 2020 | 596 views


You can try the following: 1# Check the main power cable & make sure it has 110V (Do not run the machine with long extension cable).2# Check all harness connection.3# Check keyboard cable connection on back of control board.4# If all the cable connection is good then you may need to replace the control board.

Measuring Tools... | Answered on Aug 02, 2020 | 5,625 views


Those are precision devices and require factory check up and calibration at regular intervals. Contact your dealer.

Measuring Tools... | Answered on Aug 01, 2020 | 160 views


Please contact a radio shack for this info.

Measuring Tools... | Answered on Jul 07, 2020 | 1,737 views


Reset display by pressing the RESET button, located on the back of the display unit inside the battery compartment. Date and time will need to be entered after a reset. Flashing of the outdoor temperature is generally an indication of wireless interference.
https://www.acurite.com/media/manuals/00754-instructions.pdf
Hard Reset:
  1. Bring both the sensor and display unit together and power down by removing at least one battery from each and/or removing the power cord.
  2. Make sure the A-B-C switch on both units matches. ...
  3. Reinstall the battery in the outdoor sensor.
  4. Reinstall batteries and/or power cord into the display unit
https://support.acurite.com/hc/en-us/articles/360013641694-3-in-1-Reset

Measuring Tools... | Answered on Apr 29, 2020 | 62 views


You may use following removals Tools
  • Moving Dollies
  • Pallet jacks
  • Hand Trucks
  • Hydraulic Tools
You may also get information about Removals Tools Here
Removal Companies Tools

Measuring Tools... | Answered on Apr 24, 2020 | 177 views


https://support.acurite.com/hc/en-us/articles/360007555574-Temperature-is-Flashing-Stuck-or-Showing-Dashes-on-a-Basic-Multi-Sensor-Display-

Measuring Tools... | Answered on Apr 22, 2020 | 133 views

Not finding what you are looking for?
Radio Shack Wireless IndoorOutdoor Thermometer System Logo

5 questions posted

Ask a Question

Usually answered in minutes!

Top Radio Shack Measuring Tools & Sensors Experts

Cindy Wells

Level 3 Expert

6220 Answers

Brad Brown

Level 3 Expert

18562 Answers

Harrie

Level 3 Expert

6746 Answers

Are you a Radio Shack Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...