20 Most Recent GE Stainless Steel Built In Trash Compactor GCG1580RSS - Page 5 Questions & Answers

If the light comes on the changeable thermal fuse is OK under a the single screw inch-long cover on the pull-out control. I bought mine a a g-sale like new for $3.00 and found it heating but very cold 200*. on the under side of control you will see a 1/4" white plug flush with the surrounding white plastic to the left of the "for household use only" sticker. With an eyeglass screwdriver, pry this plug out and if your driver is long and small enough, you will engage the thermostat factory calibration screw. turn it counter clock-wise 1/4 turn and check for increase in temp. Mine took a half turn to zero it in to 375* K.L.

Here is a direct link to the User's Manual for that device:

http://www.fixya.com/support/p237043-ge_slim_spacemaker_7_5295_cd_shelf/manual-11873


or you can find it here at this link as well:


http://static.fixya.com/Manuals/G/GE/75295_Clck_R_4FB4DC9750E55A3910C4BE1CD2294289.pdf


To view the Owner's Manual with Operating Instructions just use your mouse to click on the link, which is the underlined and highlighted text just above. This will open a new web browser page automatically for you and allow you to view the information at the website indicated and the contents of the Owner's Manual.

You may need ADOBE READER installed on your computer to read PDF documents.
You can download this free at WWW.ADOBE.COM if necessary.
Click on the DOWNLOAD ADOBE READER button on right side of the ADOBE home page when you get there, then follow the onscreen instructions to install the software on your computer.

Please comment back here to this page if you have any details to add, have any questions, have difficulty accessing the links, or just require further general assistance and I will respond as soon as I see it.

I hope that was helpful to you, good luck and take care.

Joe.

change the jets propane jets are a little larger then natural gas

The white wire has to be connected to neutral wire for timer clock to operate.
Open following links to help with wiring:
http://waterheatertimer.org/GE-timers-and-manuals.html#15070
http://waterheatertimer.org/images/GE-15070-wiring-1-500.jpg

There's a shorted circuit happened inside the microwave oven. A interlock or door switches that are shorted will cause a blowing breaker. Also a shorted magnetron tube will cause it to blow breaker.
Until a shorted parts is found and replace with the same ratings, that will the only thing a blowing breaker will stop. An indication that a short is no longer occur is the fuse, if the replace fuse is not blown it means normal operation will follow.
Call a service technician to do that, it is not simple thing to do for a do-it-your selfer.
Goodluck.

Hi
If everything else is working fine then it seems the issue is with the door switch, if this switch is bad control senses that the door is still open and so won't heat. Please check this video to test the door switch: Hope this helps...please post back for further assistance.
Daniel

As far as I can tell parts are not available for this skillet. If you can get me a model or part number I would be happy to do more looking. Thank you.

Hi,

The ignitor is not working right and is going bad....
have the repair man replace the ignitor, or DIY....
Check out this tip about your problem...

Oven not Working or Oven not Heating

Oven Problems Replacing the Igniter


heatman101

Try here. http://www.shavers.shop-1st.biz/SHAVERS-SALE/0-Ge-mixer-1-NEW.html

Hello, Let the unit cool down from the last wash. This will allow the parts to contract. If you look under the door there is a cavity below the dishwasher which usually has a faceplate. Sometimes it has screws holding the faceplate on. Remove the faceplate.

There are leveling screws on each corner of the dishwasher cabinet bottom. Right now you do not know whether the doorlatch is jammed because the base is too tight and is pushing the dishwasher into the countertop; or if the leveling screws are loose and the dishwasher is hanging FROM the countertop.

Most likely the leveling screws turned themselves looser from the vibration of the appliance operating. Just adjust the levelers properly and the latch should work normally afterwards. When you manage to get the door open, make sure you level the unit with some water in the machine bottom and some heavy dishes in the top tray. The front of the dishwasher should not be lower than the back.

I hope my solution is very helpful in fixing your product.

Not much to go on here but either the compressor has failed, the starter for the compressor has quit, the thermostat is not working, or you have thrown a breaker.