Top 20
Mitsubishi WS-65611 65" Rear Projection Television Questions & Answers
Blue colors are turning green
For model listed here, a issue likely on the Blue CRT circuit board, bad grounds and even seen a tiny crack on that board do this, sounds like blue is dropping out.
12/16/2012 3:15:26 AM •
Mitsubishi...
•
25 views • 0 helpful votes
Ws-65611 color shadows
You need to turn down the voltage on all 3 crt's. You have a red one, a blue one and a green one. Slowly adjust the knob down until you don't see the shadow any more. Then adjust your color in the user menu.
8/21/2012 5:51:57 PM •
Mitsubishi...
•
135 views • 1 helpful votes
How to reset factory settings ws 65517
If you contact Mitsubishi the set has three hidden menus---convergence adjust, circuit adjust and OPTION MENU.Each model uses a four digit code with menu and for example 4750 and in the Option menu is the option to do the hard reset for the set---The wipes all labels (dvd etc) and puts set back to default on all factory settings.You might find it if you GOOGLE THE MODEL NUMBER with option menu after it...........
3/18/2012 8:10:06 PM •
Mitsubishi...
•
335 views • 0 helpful votes
65" mitsubishi rear projection tv won't turn
IF model number posted is correct and green power light comes on for a few seconds and then goes off:On front of set press and hold both the Menu and Input (device) buttons at the same time for at least five seconds and release both buttons.Power light will then blink a two digit error code like 2 blinks, 2 blinks, a pause and repeat it several times.Let me know what error code is found and I will tell you what it means.SD TECH
10/9/2011 11:29:50 PM •
Mitsubishi...
•
814 views • 1 helpful votes
My color is gone. Some
This model has three picture tubes and they will not cause loss of color.
It does not have a bulb.
Are you connected via the cable fitting on the set or the A/V jacks on the back of the set?
The more you tell me the better I can help.
SD TECH
The picture on my Mitsubishi
No,tv have a problems known as a convergence problems,it is dead.This problems it is the tv board that call the convergence board it is dead.This convergence board must require to be replace 2 STK convergence ICS and some or all of it resistors too on the convergence board too.To fixed the tv convergence board to solved the tv convergence picture.The shop,will cost u like $300-350 for parts and labors.
4/19/2011 11:54:46 PM •
Mitsubishi...
•
329 views • 1 helpful votes
How do I hook up a Sharp Bd-HP24Ua Aquos BD
The only option you have is to connect it via Component cables (Red, Blue, Green) and analog audio cables (Red, White) to get an Analog HD 1080i at best picture and analog stereo sound. I have to tell you though, your BD player is better than your TV and by using it on this TV you are missing out on the unit's full potential of features. I would highly recommend you consider upgrading and if your're looking to save a few bucks and get an amazing picture, consider upgrading to a Mitsubishi DLP. They are as low as $799 for 60".
4/23/2011 8:34:11 AM •
Mitsubishi...
•
89 views • 0 helpful votes
Convergence problem on ws65611
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.
Common Symptoms include....
- Screen looks 3D
- Colors don't line up
- One or more colors can't be adjusted when using the convergence menu.
- Screen is bowed or warped.
- TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some images of convergence problems.
SOLUTION #1
For more more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
Or goto the site www.TvRepairKits.com for the parts and instructions on how to fix it yourself.
4/14/2011 3:13:52 AM •
Mitsubishi...
•
110 views • 0 helpful votes
MY TV IS OUT OF
have you tried adjusting the convergence on the tv
once they get older or get moved you need to do this
go through on screen menus and look for adjusting convergence menu and follow on screen instructions
good luck!
3/25/2011 8:28:13 PM •
Mitsubishi...
•
142 views • 0 helpful votes
I have a Mitsubishi WS65611 I understand that the
YES, you either have a fuse that went out or the convergence IC went out... Sometimes it just comes unsoldered and causes the same effect. You need to locate this "IC" and tap on it with something non metallic. Like a ruler or a stick. While the tv is running and crosshatch is up on screen. If the lines get close as you tap on the IC or bang on the tv. then fuse is good and the tv might just need to be resoldered on that CONVERGENCE IC. Let me know how this works for you and if you have any questions give me a call @ 502-773-7969 and i can help u out further.
HAVE A GREAT DAY....Sincerely HDTV GURU JAY
3/15/2011 7:08:47 PM •
Mitsubishi...
•
95 views • 0 helpful votes
I have a WS-65611 that I have replaced the caps on
Did you run the error code operational check? In not unplug the set and plug it back in. Press and hold the DEVICE and MENU buttons for 5 seconds and release. The LED should flash a certain number of times a short pause and another series of blinks. Count the number of blinks before and after the pause, and let me know.
3/21/2011 9:30:15 PM •
Mitsubishi...
•
53 views • 0 helpful votes
Gets power and sound but
Bulb is probably dead, you can find a bulb online and put it into the TV. Refer to page 79 of your owner's manual to see how to disassemble the TV(available online
here).
Not finding what you are looking for?