20 Most Recent Hayward SP3015EEAZ Super II Pump 15Horse Power Questions & Answers

My pool motor tripped my breaker. When I reset the

The title description is a Hayward Super II 1.5 HP but the part number you gave is for a StaRite MaxiGlas pump. Either way the motor needs to be replaced.
The best way to find out what you need is to look at the part number on your impeller. With that information whoever you buy the motor from will be able to get you the correct pump and seals..

Hayward... | Answered on Nov 03, 2013

1 Answer

I have a hayward super ii pump model sp1615z1

There is no cheap fix for a burned up motor...you'll need to replace it. You can replace just the motor for about half the cost of a whole new unit. When you replace the motor you should replace the pump seal as well. Your motor number should be UST1152 for the 1.5 HP and the seal number a 201.

John

Hayward... | Answered on Jun 27, 2011

1 Answer

H200fdn pool water heater. Why doesn't blower start?

its trying to start check voltage to fan if ok bad fan motor if no check safety circuit

Hayward Pool &... | Answered on Dec 19, 2020

1 Answer

I have a Hayward h400 heater I changed my display bored because It was shot but now it’s displaying code BO but when I try to put it in service mode nothing happens it stays in stand by mode what should I do

https://haywarddocs.info/wp-content/uploads/2017/10/UHS-Troubleshooting-Guide.pdf

Page 34-35

Hayward Pool &... | Answered on Nov 25, 2020

2 Answers

Hello, have a Hayward cspaxi 11kw for 2 years and now when I try to turn on it exploded and the breaker trip. I tried twice and it did the same. Any thoughts what could be wrong?

shorted heater element

Hayward Pool &... | Answered on Sep 13, 2020

2 Answers

I have a Hayward heater H400. When it turns on it runs for 30 to 40 seconds starts making a banging noise temperature starts moving up and heater turns itself off. Error codes 5F and H5 appear or it could be SF. Thx, Tom

sounds like it doesn't have any water in the boiler

Hayward Pool &... | Answered on Sep 12, 2020

2 Answers

Our Hayward gas heater keeps giving us a H5 error

Could the Error code be HS? That is high temperature limit. Perhaps you' don't have enough flow, allowing the heater to heat the water to a temperature higher, than the thermostat setting. Make sure your bypass valve is closed, allowing full flow through the heater. Check your filter pressure differential , and skimmer baskets.
You didn't give your model number, and there are many models. You can go the Hayward website below and select your exact model number and download the manual. The manual will explain each error code.
http://www.haywardnet.com/inground/products/manuals.cfm

Hayward Pool &... | Answered on Jun 07, 2020

1 Answer

Hi i have an old hayward h250 pool heater. The problem is that it starts but after 3 seconds it turns off. It’s as if it doesn’t detect who is on and it goes out for safety and after 3 attempts it displays the code 1F. But it starts, what is wrong?

http://pyrate.org

Hayward Pool &... | Answered on May 03, 2020

0 Answers

My Hayward vac gets stuck and stays in the same place until I physically move it, which means I have to watch it the whole time it's running.

Hayward Pool &... | Posted on Jan 16, 2020 | Be the first to answer

1 Answer

How do you get to centrifugal switch on Hayward PowerFlo matrix

Are you sure it has a centrifugal switch?
Capacitor start/ capacitor run have been the standard for a good number of years.

Hayward Pool &... | Answered on Oct 26, 2019

1 Answer

Manual for Hayward pool products DE 4800

Hayward's website has manuals for all their products.

Hayward Pool &... | Answered on Oct 26, 2019

0 Answers

Hayward h100id troubleshooting

Hayward Pool &... | Posted on Sep 21, 2019 | Be the first to answer

0 Answers

Can't get impeller off Hayward PowerFlo matrix, tried holding with screwdriver but can't break free

Hayward Pool &... | Posted on Sep 15, 2019 | Be the first to answer

1 Answer

I have Sumheat S3 Hayward pool heater I also do not have 24 V output between the blue and yellow cables coming from the transformer. Do I need to replace the transformer? Thanks Cecilia

The 24v is called the secondary and sometimes called the out-put. Make sure you have 240v on the primary, sometimes referred to as the in-put. If you have primary voltage then you should have secondary voltage, if not then replace transformer. Make sure the secondary, 24v control fuse is the correct size and present. If the secondary is shorting together or to ground somewhere, it will cause damage to the transformer.

Hayward Pool &... | Answered on Aug 18, 2019

2 Answers

I have a Hayward H400 pool heater. I don’t heat my pool so I never use it but I do turn it on once or twice a year for about five minutes to make sure it’s working, which right now it fires up just fine. The problem I am having is once the pump turns off, the blower on the heater turns on & stays on. I can’t get it to turn off unless I cut the power. This is obviously a problem because I can’t have the pump on a timer because as soon as the pump turns off, the blower on the heater will run for 16 hours until the pump kicks back on. I’ve done a lot of research & can’t find a solution or anyone who has experienced this problem. Any advice would be appreciated.

Call a qualified electrician. More information would be needed to accurately trouble shoot your issue. Do you have automation connected to your heater? Is the heater trying to fire when the pump is off or is it ONLY the fan?
Try disconnecting your Water Pressure switch on the heater and see if the issue stops. With WP switch disconnected the heater should not work and the fan should stay off. Replace WP switch and see what happens.
Call a QUALIFIED electrician.

Hayward Pool &... | Answered on Aug 12, 2019

1 Answer

I have a Hayward pump it says it has a switch on the pump but I cannot find it where is it located

Underneath the back cap on motor

Hayward Pool &... | Answered on Jul 30, 2019

1 Answer

Hayward power flo lx pump humming

Check for proper supply voltage and that the impeller moves freely. If these are good then likely a bad capacitor.

Hayward Pool &... | Answered on Jul 30, 2019

1 Answer

Is it possible to program a Hayward prologic pool controller to run an action every second day? I have aux 6 on a countdown timer and want it to run every second day.

the prologic control unit will not offer programming for what you seek. the most detailed timers will offer weekday or weekend for each pump speed. you may want to get a remote system so you can control functions from your smartphone

Hayward Pool &... | Answered on Jul 26, 2019

1 Answer

Vapor lock

try filling your hose by holding it in front of the return jet. once filled, hook the hose up as normal

Hayward Pool &... | Answered on Jul 26, 2019

1 Answer

Hi. I have a Hayward H350FDN pool heater that is Doing this: • Turn on and Temp at 65 • On for 3 1/2 min then shuts down • Restarts and then on for 5 min, shuts down • Restarts and then on for 2 min, shuts down • Restarts and then on for 8 min, shuts down • Temp 66 • Restarts and then on for 10 min, shuts down • Restarts and then on for 2 1/2 min, shuts down • Restarts and then on for 1 min, shuts down • Restarts and then on for 1 min, shuts down • Restarts and then on for 10 sec, shuts down • Restarts and then on for 40 sec, shuts down • 1F error code I just replaced the heat exchanger prior to this happening. Any ideas????

it almost sounds like the temperature sensor is in the wrong place. that or the flow is inadequate for the heater to run. if you have a sand filter, put it on 'whirlpool' or 'recirculate' and try to run the heater.

Hayward Pool &... | Answered on Jul 26, 2019

Not finding what you are looking for?

2 questions posted

Ask a Question

Usually answered in minutes!

Are you a Hayward Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Have a manual for Hayward SP3015EEAZ Super II Pump 15Horse Power? Or just drag it here!

View Most Popular

Hayward Pool & Spa

Hayward Pool & Spa

pool motor tripped breaker when reset

Pool & Spa

20 Most Recent Hayward SP3015EEAZ Super II Pump 15Horse Power Questions & Answers

My pool motor tripped my breaker. When I reset the

I have a hayward super ii pump model sp1615z1

H200fdn pool water heater. Why doesn't blower start?

I have a Hayward h400 heater I changed my display bored because It was shot but now it’s displaying code BO but when I try to put it in service mode nothing happens it stays in stand by mode what should I do

Hello, have a Hayward cspaxi 11kw for 2 years and now when I try to turn on it exploded and the breaker trip. I tried twice and it did the same. Any thoughts what could be wrong?

I have a Hayward heater H400. When it turns on it runs for 30 to 40 seconds starts making a banging noise temperature starts moving up and heater turns itself off. Error codes 5F and H5 appear or it could be SF. Thx, Tom

Our Hayward gas heater keeps giving us a H5 error

Hi i have an old hayward h250 pool heater. The problem is that it starts but after 3 seconds it turns off. It’s as if it doesn’t detect who is on and it goes out for safety and after 3 attempts it displays the code 1F. But it starts, what is wrong?

My Hayward vac gets stuck and stays in the same place until I physically move it, which means I have to watch it the whole time it's running.

How do you get to centrifugal switch on Hayward PowerFlo matrix

Manual for Hayward pool products DE 4800

Hayward h100id troubleshooting

Can't get impeller off Hayward PowerFlo matrix, tried holding with screwdriver but can't break free

I have Sumheat S3 Hayward pool heater I also do not have 24 V output between the blue and yellow cables coming from the transformer. Do I need to replace the transformer? Thanks Cecilia

I have a Hayward pump it says it has a switch on the pump but I cannot find it where is it located

Hayward power flo lx pump humming

Is it possible to program a Hayward prologic pool controller to run an action every second day? I have aux 6 on a countdown timer and want it to run every second day.

Vapor lock

Not finding what you are looking for?

Ask a Question

Popular Products

Hayward SAND FILTER, PRO SERIES

Hayward H-series Electronic Gas Pool Heater H400

Hayward 250kbtu Ng Pool Heater - Inground

Hayward 2HP Pool Pump Motor A O Smith Electric Pool...

Hayward 1.5 Hp Northstar High Performance Pump

Top Hayward Pool & Spa Experts

john h

Marvin

Paul Carew

Are you a Hayward Pool and Spa Expert? Answer questions, earn points and help others

Manuals & User Guides

Hayward Pool & Spa

pool motor tripped breaker when reset