20 Most Recent Mitsubishi WS-65907 65" Rear Projection Television Questions & Answers


Cannot disable net command

It has to be cleared after the software has been downloaded to your computer from the Harmony website.
12/15/2017 4:30:36 AM • Mitsubishi... • Answered on Dec 15, 2017

Why does my picture have a washed out appearence about it?

think you have bad solder the best way to find out if you do have bad solder take tool that is rubber and tap on the bord of the big screen to see whear the bad solder I thinking it maybe by the conv chip are at stk392-120 or 110.. thear are two of them mit are knowing for bad solder.. I done a lot of them I been doing them for 13 or more.. STK392-110 - Stk392-110 Sanyo IC 18-pin SIP The STK392-110 is a convergence correction circuit IC for video projectors. It incorporates three output amplifiers in a single package, making possible the construction of CRT horizontal and vertical convergence correction output circuits for each of the RGB ...
11/21/2013 12:08:21 AM • Mitsubishi... • Answered on Nov 21, 2013

Mitsubishi WS 65819. Had convergence problems.

Your post is showing 2 different model # which one is yours the WS65819 or the WS65907?
4/10/2013 6:29:22 PM • Mitsubishi... • Answered on Apr 10, 2013

I have a WS-65907 tv, it wont turn on

Mitsubishi self check: MOST OF THESE SETS HAVE A SELF DIAGNOSTIC: UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER LIGHT COMES ON FOR A MOMENT AND GOES OFF. PRESS AND HOLD "device"(input) and "menu" buttons on front of tv for at least 5 seconds and then release both together. Watch for power light to blink in a sequence: 1 blink-then 2 blinks-------no error 2 blink-then 1 blink-------X-ray protection 2 blink-then 2 blink-------SHORT PROTECTION******* 2 blink-then 3 blink---------deflection circuit problem 2 blink-then 4 blink---------vertical circuit problem ******2, then 2 is most common---usually means one of the fuses that protect the Convergence IC or IC's is blown---set will detect no voltage to convergence IC and shut down. SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES AND THEN TO GET IT TO REPEAT MORE YOU HAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN. IF IT IS 2 AND THEN 2---USUALLY CONVERGENCE CIRCUIT PROBLEM let me know what you find--hope that you find 2 blinks, a pause and two blinks--this is the most common and easiest to fix.
1/3/2013 12:52:18 AM • Mitsubishi... • Answered on Jan 03, 2013

I have a Mitsubishi WS-65907 that won't turn on

change here the two stk-392-570 convergence chips and one of the two pico fuses connected to them, if you still need help I have instructions for this repair in this set--start to finish.
12/22/2012 3:48:28 AM • Mitsubishi... • Answered on Dec 22, 2012

Static on Powering on

You can start out by resoldering all poor solder connections and look for bad capacitors they will be puffed up on Top.
10/9/2012 12:37:29 AM • Mitsubishi... • Answered on Oct 09, 2012

Does this moel have a digital converter built in

No but if you tell me what you are trying to do.....To make a comment: press the "make a comment button" on this page.
3/26/2012 3:29:09 PM • Mitsubishi... • Answered on Mar 26, 2012

S my picture not comming in clear and has lines threw it?

Misubishi----ws-65907 is the model number?Two common issues here---one is convergence where picture is somewhat or very 3d looking---I can if model number correct tell you how to fix that and second issue is some models get black lines that look like interference which is a more difficult problem to deal with.Let me know which best fits your issues.
3/14/2012 2:14:18 PM • Mitsubishi... • Answered on Mar 14, 2012

Picture becomes cloudy on my

You have a contaminated picture tube. One of the three (red, blue, green) will need replacement fluid. The best source with instructions on how to do this, is to see the website. TVRepairKits.com. They will have complete instructions and photos. I have used this site and quite impressed. Thanks for asking and show all hands of support!
9/1/2011 4:38:40 AM • Mitsubishi... • Answered on Sep 01, 2011

Colors separate when tv has been on for a short

The model indicated uses two of the STK-392-570 convergence chips---one is bad and both are located on the middle circuit board inside the set.

This could be a do it yourself repair (total parts will cost under 30 dollars) and I have step by step instructions for this repair in this model.

I have seen a lot of these and it is always one of the two chips (both must be replaced at the same time)

Let me know if I can assist here with your problem.

7/25/2011 7:41:01 PM • Mitsubishi... • Answered on Jul 25, 2011

We need to figure out

All projection TV sets have two very common problems. One is convergence ( 3D/Warped video or dead set) the other is CRT fluid ( Dull Video). Here are more details and solutions for both.

Common Problem #1) Convergence has gone out

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. In some cases the TV will also not show any video. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

  • Screen looks 3D, wavy, or has a shadow or shadows
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some pics of convergence problems.



You can get the correct parts, step by step photo instruction guides, and support from www.TvRepairKits.com or click here

Common Problem #2) CRT Fluid is Cloudy

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.

Picture of a set that needs the fluid changed.

TV set after fluid change



You can get the correct parts, step by step photo instruction guides, and support from www.TvRepairKits.com or click here
5/9/2011 1:52:50 AM • Mitsubishi... • Answered on May 09, 2011

I have a 1999 model...when you turn it on the

Goe to the setup menu and turn off closed caption.Does it do this on all inputs. Closed caption is only on rf input as far as the tv is concered. If this is happening on input which is connected to cable box or sat reciever call your serv provider.
3/7/2011 10:25:31 PM • Mitsubishi... • Answered on Mar 07, 2011

Mitsubishi WS-65907 HD TV screen

try and run the convergence if that doesnt work you may be looking at some bad stk packs they arnt very expensive but they arnt easy to install
2/11/2011 3:57:58 PM • Mitsubishi... • Answered on Feb 11, 2011
Not finding what you are looking for?
Mitsubishi WS-65907 65" Rear Projection Television Logo

Popular Tags

83 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76851 Answers

Jaime Hernandez

Level 3 Expert

2351 Answers

Cindy Wells

Level 3 Expert

6588 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Mitsubishi Televison & Video

  • Mitsubishi Televison & Video

Most Popular Question

ws 65907 tv wont turn

  • Televison & Video