20 Most Recent Mitsubishi WS-65513 65" Rear Projection HDTV - Page 6 Questions & Answers

http://www.jyerdon.com/tv/

If it`s a 65513 mitsu, this will fix the flashing green light, most of the time, e-mail me with any questions, good luck


[email protected]

replace the DM capacitors. Here is a link to the repair kit which contains the replacement capacitors and instructions with pictures.
http://servicemanuals.vstore.ca/product_info.php/pName/mitsubishi-v23-dm-repair-kit/cName/repair-kits

When the repair person gets to your house, first of all, let them work. Then once all is done ask them what they think is wrong with the set and how much it will cost. I think that you have lost the use of the green CRT, and you may just need a driver IC to fix it. You can ask the technician these questions and get a straight reply.

I hope this information allows you to resolve this issue.
If I have helped you, please help me, and rate this suggestion the highest FixYa rating. (Two Thumbs Up) If you cant rate this post with the highest rating, then please comment to this post and I will try to help you further.

dvd players use component or hdmi cables for hookup
select the proper input on the mitts

you need the V23 DM kit available at the following link it contains the caps and instructions.
http://servicemanuals.vstore.ca/product_info.php/pName/mitsubishi-v23-dm-repair-kit/cName/repair-kits

Sure, you will need to replace the power supply circuit board asap. this will fix your issue.

The TV is on protect mode.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

Also ensure that the fault is not coming from a faulty receiver box sending bad signal, check if you get same problem with no receiver box or dvd connected.

If that does not work, and you keep having a flashing led on front of the TV, and tv turning off by itself after a while, that indicates a fault condition.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible reasons.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , startingthe flashing light.


If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

Common faults that can occur are a blown capacitor on power board, a convergence IC has blown, or a fault on Digital board.

Check also the video cable or any external connection cable, if the cable is shorting, or the connector is bad, you can get same flashing state because of the video cable.


If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

You can find parts here,

Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

Electronic Replacement Parts: Plasma & LCD TVs, Appliances |

mmm try this.... do u guys have the yellow white red cables hooked up to the front of the tv from the wii console? try loosening them up. worked for me. let's see how long it lasts .... !!!!

replace the capacitors on the DM that will usually take care of it, when the led is blinking the DM is trying to complete the boot sequence . Heres a llink to the DM repair kit for your model which comes with instructions
http://servicemanuals.vstore.ca/product_info.php/pName/mitsubishi-v23-dm-repair-kit/cName/repair-kits

According to " Consumer Affairs. com", the problems with seris of Phillips plasmas are innumberable. And they all start with the flashing red light, from 3 - 7 times. Baased on the information you gave, there is something wrong with the TV itself, not your perifrials. I would contact Phillips/ Magnavox to see if they will pay for an authorized sevice center visit, or even ship you a part to solve the problem.

This is definitely a problem you don't want to tackle at home. TV's are made to kick off when it knows a problem exists. The warped pic is a "convergence IC" issue. That IC needs to be replaced by a tech, either in home or in shop.

Make sure the SAP (second audio portion ) is not activated

I would say without taking voltage readings, your Regulator IC in the power supply has had it. It's still worth repairing if that's the only problem. Contact your local Service co. for an evaluation and an estimate first.

mike, give me an email address and I can send you a PDF!

The documents are on it's way. Good luck

Thats a common problem caused by defective capacitors on the DM PWB which prevent the set from booting up. The V26 DLP DM kit at the following link will usually repair that issue and it comes with step by step instructions on how to do the repair. Look under the repair kit category.
http://servicemanuals.vstore.ca/

You need to run an external antenna feed to the air DTV input jack, bottom left. You can use your loop out if you already have an antenna connected to your antenna A input jack. Create a DTV device, then run your antenna setup for DTV.

Hey guys the problem is a 3 pin 9 volt regulator

Please rate!
First the yellow tinge is due to the blue STK convergence IC possibly being burned. Usually on the right lower side,sccessed from the back, is a module with 3 black stk's on it. If you see the stk's then replace all 3. Not one as the others will blowreally soon. Also check to see if green coils are burned if, so replace them. Get parts from matelectronics.com. Good source and inexpensive, about 40 bucks for the parts...Give a good visual and then proceed. be careful! high volts still in there, but don't worry...

It looks like you have a convergence problem here, probably a defective convergence IC.