20 Most Recent
Questions & Answers
I push the power button the power light come on i
Do the self check this model has:
Turn set on and when green power light goes out: press and hold both the Menu and Input buttons on the front of the set for at least 5 seconds and then release both buttons.
The power light will blink a two digit error code: most common one is 2 blinks, pause and 2 blinks---it will repeat the error code at least 5 times.
Let me know what you find--2,2 is the most common and may be a do it yourself repair.
I am here to help you--if this information is helpful rate this solution as very helpful as I do this here for free.
REGARDS, SD TECH
Our WS-55313 Mitsubishi Projection screen tv was
do the self check this model has.
When green light goes off press and hold both the input and menu buttons for five seconds and release both buttons.
The power light will blink a two digit error code like, two blinks, two blinks, a pause and then repeat it several times.
let me know what the error code you find is and I will let you know what it means.
Mitsubishi hdtv 1080 what are the blinking green light codes
ost models have a self-diagnosis feature to help determine shutdown problems.
To enable this feature do the following....
1) Turn the tv on and then let it shutdown
2) Press the input and menu buttons on the front panel simultaneously and hold them in for 5 seconds
3) After 5 seconds the power LED on the front panel will blink a two digit sequence.
This will commonly be one set of blinks followed by a short pause then another set of blinks.
This will repeat around five times.
1 - 2 = no error detected
2 - 1 = X-ray protect (high voltage or beam current)
2 - 2 = Short protect (short detected - commonly caused by convergence failure - to repair this check out site for a convergence kit)
2 - 3 = Deflection protect
2 - 4 = Vertical protect
Note: A constant blink on certain models will typically be caused by a fault in the DM model. To repair this check out site a "blinking green light kit"
Need instructions of 55"t.v model ws55513 d m board with capacitors
- Try going To http;/www.techlore.com/24711/Mitsubishi-Blinking-green-light-repair-procedure.... It Suppose Load up about Nine Pages of Stuff on how to fix the (DM Module Board) If you Can't Fine The 1000 uf 35 wvdc Operating temperature 105 C: Electrolytic capacitor Try The Radio Shack one It Rated At 40 To+ 85 C It Will Work If You Can 'Fine The Other one !05 Deg. C Type -----Check Out This One Too 78 Pages (http://www.techlore.com/x/article/24711/Mitsubishi-Blinking -Green-Light-Repair-Procedures.(Ps) It Want Hurt To check The Ones In the power supply area,other Area .Too You might Have Change them All If You Have All The 1000 uf Check If they Showing Under Less Then The are Rated at Then It Want Hurt To Them All
Screen stays blue and wont show the picture
TV may be on the wrong input and that will give you a blue screen. When you turn the TV on and the screen starts lighting up it should show on the screen what input the tv is on. If it is not on correct input change input with the TV remote or buttons on the tv. If it is on the correct input try a power cycle on the cable box, just unplug the cable box power cord for a few seconds and then plug it back in. If neither of these solve the problem describe how the cable box is connected to the tv.
Mitsubishi Daimond Series 65" Model#WS-65909
Most common repair is one or two open fuses in power supply
and bad convergence Ic's = expensive repair.........Also, have
the tech check for coolant leakage from CRT's...........T.
Ws 55515 tv
What is the problem you faces with this TV? Provide more details please. If you are somewhat sound in electronics, check this site. http://electronicshelponline.blogspot.com/ Pull up older posts there, either by its left side bar, or
see it in Timeslide option. Troubleshooting procedure to many brands TVs are given in detail.
Not finding what you are looking for?