Top 20 Mitsubishi WD-52525 52" Rear Projection HDTV Questions & Answers

The contrast setting may be misadjusted.

Mitsubishi... | 154 views | 0 helpful votes

If you wish to get some details; visit the site linked here. Pull up older posts.
Line faults & possible causes to LCD & Plasma screen are given with illustrations. You can get an idea about the fault to an extent. Faults to all LCD & Plasma screen are similar, irrespective of its brand and screen size.
Search the site by type in the "BRAND NAME" of your device; (Exclude the model number), in the "Search box at the top right of the display window of the Homepage" to get gathered related posts

Mitsubishi... | 283 views | 0 helpful votes

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience.

Mitsubishi... | 518 views | 0 helpful votes

usually changing the aspect ratio will do it .

Mitsubishi... | 136 views | 0 helpful votes

The ballast for the bulb is the culprit. That is the circuit board directly wired to the bulb. You can get a replacement on line at:
TV Parts Universal TV Stands DLP Chips ShopJimmy It's not difficult to change it yourself .

Mitsubishi... | 143 views | 1 helpful votes

Seems to be the inverter board that controls the bulbs! With the TV on if you shine a torch at the screen can you see a faint picture? If so it is the inverter board that needs replacing!

Mitsubishi... | 146 views | 0 helpful votes

Yes, there are three. The chassis fan, the exhaust fan and the fan for DMD.
The chassis fan is going to be mounted behind an intake air filter on the right side of the cabinet from the rear view. I am providing you the service manual.

Mitsubishi... | 110 views | 1 helpful votes

Dead pixels can not be repaired.
The model# WD-52525 you provided is for a DLP TV.
If you are seeing white dots on the screen it is due to a bad DMD chip or light engine. Unfortunately, it is not a cheap fix.

Good luck

Mitsubishi... | 150 views | 0 helpful votes

The monitor link is not a standard DVI connection, it was used to connect a Mitsubishi HD set top box. You can connect your cable DVR using component video cables and get HD that way, up to 1080i but not 1080p

Mitsubishi... | 405 views | 1 helpful votes

Right next to the other controls on the TV, it is recessed so you will need a paper clip or ball point pen to press it.

Mitsubishi... | 1,059 views | 0 helpful votes

Hi Terrence
Probably bad connections in the lamp base.
Heat damaged or corroded or Over temperature sensor tripped.
When it goes out next, Bump it or Tap it to see if its mechanical contact problem. That will help diagnose where the problem is
Good Luck

Mitsubishi... | 24 views | 0 helpful votes

You might want to try a One for All remote and use its code search function to find the code you need. If you do not have instructions, you may be able to obtain them from the One for All site

Mitsubishi... | 45 views | 0 helpful votes

The pop was a high voltage arc of electricity that blew some vital components on the main circuit board. The unit is of no use now. Repairs are far more than replacing the TV.

Mitsubishi... | 120 views | 2 helpful votes

What does the TV do when you try to turn it on?

Did you put the lamp door back on before you tried to turn the set on?

Mitsubishi... | 50 views | 0 helpful votes

The lamp housing has some screws you need to loosen, did you do that?

Mitsubishi... | 30 views | 0 helpful votes

you have a bad dlp chip hear a link for you so it will help you to unstay.
how the light eng

Mitsubishi... | 137 views | 0 helpful votes

Ballasts were sometimes problems with this set, but I also ran into problems with lamp thermal sensor. It's a small rectangular device sort of cream color and about 1/8th X 3/16th X 3/4 inch in size with lead coming out of one end. Also check safety interlock switch, which is actuated by lamp access cover being properly closed.

Mitsubishi... | 93 views | 0 helpful votes


Mitsubishi... | 97 views | 0 helpful votes

the lamp eng it bad you need to replace the dmd or the hole thing the eng, whear the lamp in stall at and i done a lot of them to and that cost a lot 1000.00 plus the core you need to send back to mitsubishi you may whant to call them to see if it under wearenty if not that will till you how much it cost to have it a big job it chang them to about 2hours to replace them the lamp eng ..good luck i hope this help you my self don,t like a dlp at all the lamp cost to much to replace for lasting just a year. lamp should last about 2 years but i not seen a lamp last that long at all..the samsung is just as bad... will good luck

Mitsubishi... | 72 views | 0 helpful votes

Not finding what you are looking for?
Mitsubishi WD-52525 52" Rear Projection HDTV Logo

1,606 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1258 Answers

The Knight
The Knight

Level 3 Expert

76407 Answers


Level 3 Expert

13434 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

WD Mitsubishi

  • WD Mitsubishi

Most Popular Question

bulb goes out after few minutes

  • Televison & Video