Top 20
Mitsubishi WS-55315 55" Rear Projection HDTV-Ready Television Questions & Answers
One yellow, one pink, and one blue spots appeared on my tv screen.
The set if projection which model here is, has arced and now each of the three picture tubes used has a tiny permanent burn mark on its screen.That is what you are seeing, the set uses three picture tubes with screens like the old tv sets===the coating has been burnt in each, want to prove it, remove rear cover and cover any one of the three lens and that mark on one tube will go a way.Not fixable.
12/23/2012 2:29:05 AM •
Mitsubishi...
•
220 views • 1 helpful votes
Horizontal deflection error
No much unless you have a service manual and a meter to test things--2,3 means a deflection problem which usually means a short in the sweep circuit.This kind of problem rarely gets fixed in the home but the set has a removable light box--all the guts come out in one piece except for the speakers and front keyboard--box can be operated out of the set as the remote receiver is up top near the lens.
5/13/2012 2:37:47 AM •
Mitsubishi...
•
133 views • 0 helpful votes
My picture in picture isn't working?
Most of these sets have two tuners--one for main and one for PIP.If main picture works fine but PIP is bad or Green? either the PIP tuner or the PIP board is bad---these were known to have the PIP have problems but it was more rare than their sets made before it.SD TECH
4/26/2012 2:06:10 AM •
Mitsubishi...
•
134 views • 0 helpful votes
My horizonal control do not work on my WS-55315
Hi Mike,First of all, thank you for contacting Fixya.com regarding on your TV problem.Based on your description, it sounds to me that the picture of your TV is rolling from left to right (horizontally). If the symptoms remain the same in all inputs, then this is an indication of faulty signal board part no. 930b901003-55. You have to replace this board to resolve the issue. Click it
HERE for the replacement.Hope I helped you.Have a nice day!Kind Regards,Mjsazon
12/3/2011 8:34:09 PM •
Mitsubishi...
•
39 views • 0 helpful votes
My Mitsubishi 1080HD model WS-55315 colors are not
The tv have a problems known as a convergence pictures problems,it is dead.Tv have any colors lines like R,G,B mis alignments,also tv have any colors shaded shadows pictures or a 3D pictures look alike?Yes,than the tv have a convergence board problems and it is dead to causes all of these problems.The tv convergence board must have to repair like replacing 2 STK convergence ICS and some or all of it resistors too.To fixed the tv convergence board to solved the tv convergence pictures problems.The tvs shops repair a DLP tv convergence board will cost u like $300-$350 for parts an labors.
9/12/2011 9:55:09 PM •
Mitsubishi...
•
194 views • 0 helpful votes
Problem with the Mitsubishi WS-55315
ONLY1 of 2 things can cause this problem----First thing to do is remove front speaker grill--it should pull out and issecured with plastic pegs--behind it you will find an inspection plate---Notice the one or two pairs of wires coming from the front keyboard of theset---remove the inspection plate and follow the wires to the right--you canunplug both plugs(most have two and they are marked with letters and differents so you cannot get them wrong)The idea here is to remove the front keyboard with its reset button etc fromthe circuit---You will still be able to try to turn the set on with theremote---These sets have a Receiver that is called a DM board--(large metal box to theleft as you look from the back) and if the power goes out the green light willblink for about 70 seconds and then go out---it is the Receiver booting up. Itis called the DM board.If disconnecting the keyboard allows the set to turn on--you have a bad resetswitch and two choices---either operate the set only with the remote or toremove the front screen and get at the reset switch (it is tiny) and removeand/or replace it.If disconnecting the keyboard does not restore the set to operation---thereceiver is bad---there are 4 or more caps and some pico fuses that can fail inthat unit---Mitsubishi no longer sells or repairs these--if it is bad and notthe caps there is a company you can send the unit to and have it repaired--ifyou need to know their name let me know---You can call them and get a quote for repairing the receiver.Let me know what more information you need--I am here to help.SD TECH
I have a Mitsubishi WS-55315
Hi
Check the componet cables if you are using them for video from the cable box, the red may of came loose.Also you could have intermittent connection the video processor IC or as we techs call it the jungle IC. It is responsible for producing all the small singals used by the set.Tapping with the handle of a screwdriver on the signal board may lead you
7/21/2011 3:04:09 AM •
Mitsubishi...
•
170 views • 0 helpful votes
The power light comes on when I turn it off and
You can check error codes. push and hold the device and menu button on the front of the set then count the blinks... usally this is the first thing us tech do when we get them in the shop. it will ussally be be a series of flashes then a pause then more flashes.. this 2 digit number will point to a certain curcit.. However sometimes it might not work... if you get a 21 this means no error.... and the problem will be harder to troubleshoot.
3/18/2011 4:30:49 PM •
Mitsubishi...
•
104 views • 0 helpful votes
Wont turn on, turn power on and tv turns off and
DO THE SELF CHECK WHEN POWER LIGHT GOES OFF.
On front of set press and hold both the menu and input buttons for at least 5 seconds and release both, power light will blink a two digit error code like 2 blinks, 2 blinks, and pause and repeat several times.
Let me know error code and I will tell you what it means.
SD TECH
12/7/2010 3:30:15 AM •
Mitsubishi...
•
229 views • 0 helpful votes
Hi i have an error
i believe that code21 on that model is vertical deflection shutdown. the repair would be very involved i suggest calling a serviceman.
12/22/2010 10:38:38 PM •
Mitsubishi...
•
78 views • 0 helpful votes
Hi my tv is the ws-55315 and i turn the tv on the
WHEN the power light goes off on front of set, press and hold both the menu and input (device) buttons at the same time for at least 5 seconds and then release both buttons.
Power light will blink an error code: most common is 2 blinks, 2 blinks, a pause and it will repeat code several times.
This is self check and will narrow down what is wrong with your set.
Let me know what code you find and I will tell you what it means.
SD TECH
11/6/2010 5:13:58 PM •
Mitsubishi...
•
235 views • 0 helpful votes
Hi, i need a circuit board for a ws-55313, tv
Encompass Parts Distribution has List of Parts/Prices and Free Service Manual that you can print out online 1-800-638-3328
Model# WS-55313 Your Model# will be printed on the back of the TV.
11/9/2010 8:31:53 PM •
Mitsubishi...
•
143 views • 0 helpful votes
My mitsubishi 55" will not turn on... when I press
Hi:
The most common failure for this model is the deflection board assembly or commonly known as a Large Signal board. The unit is going into shutdown, mode because no high voltage. Unless you are strongly electronically inclined I suggest you try to replace the deflection board.
11/10/2010 6:58:19 PM •
Mitsubishi...
•
131 views • 0 helpful votes
The picture on my Mitsubishi ws-55315 fades away
It could be oxidized contacts in the lamp housing connector. Remove the lamp housing as you would to change the lamp (follow directions in the user's manual regarding proper cool-down first!) and check the metal contact pins or blades. If they are dull or dirty, polish them with a white pencil eraser (usually the kind found on a mechanical pencil works well). Also inspect the connections to the lamp itself. If it appears they are loose or oxidized, you will need to put on a pair of clean vinyl food handler's gloves and carefully open the lamp assembly and clean them. Reinstall the lamp assembly. Do not at any time touch the bulb with bare fingers - skin oil will ruin it!
The lamp connector is the most likely spot for intermittent problems since it is high current and high temperature. It is also possible that a solder connection on the power supply board section that drives the lamp is showing the effects of thermal fatigue (cracking and oxidizing), but you would probably see much more erratic behavior, including cutout and the flashing lamp error light in that case.
It is also possible the lamp filament is on its last legs and the vibration is knocking off loose material that reduces the light output. If that is the case, there will be gray particles visible in the lamp capsule. I've seen this with a dim tabletop projector that suddenly got considerably brighter when it was picked up and turned over while it was running.
11/4/2010 6:15:14 AM •
Mitsubishi...
•
145 views • 0 helpful votes
Set comes on then turns
do the self check this model has:
when green light comes on (power) and then goes off:
On the front of the set press and hold both the menu and input (device) buttons at the same time for at least five seconds and then release both.
The power light will blink a two digit error code like: 2 blinks, 2 blinks, a pause and then repeat it several more times.
Let me know with a comment here and I will tell you what it means.
SD TECH
11/23/2010 11:51:52 PM •
Mitsubishi...
•
74 views • 0 helpful votes
Not finding what you are looking for?