20 Most Recent
Ricoh Aficio 1013F Copier - Page 7 Questions & Answers
Print quality
Ghosting can :
1-prints on the fuser roller, check if yes try cleaning it off, wait until it cools off
2-blanking lamps dirty or not working,(deletes image off the drum, before it gets ready to accept a new one)
BL mirror-(new image)
\ /
()
drum
3-Bad drum (although I doubt it this far in the process.)
Functional problem cs550
Says it fusing web end. Might want to turn the power off, wait 30 seconds, and turn the power back on. If that doesn't work a technician should look at it.
Paper a misfeed
It should be looked at by a technician to see if there is any work needed to be done on the fuser section. It could be something as simple as a bearing replacement or a fuser roller.
1013 process unit prob
You might want to check with copytechnet.com. Thats a site for copy technicians only. They have good information for problems like this.
Error msg..."close ADF cover". Where is it?
Adf : auto doc feeder
the top that you put the pappers in to copy mare than one sheet.
make sure all doors are closed.
lift doc feederas if making copy on glass look where the hinges are there should be a plunger next to one of them, that is the switch to tell it if it's open or flat. try pressing it down to see if message goes away, it may need adjusting.
Changing the number of rings on fax.
Press the "User Tools/Counter" button at the control panel.
Under the display, press the "Right Arrow" button until the display shows "4. Fax Features" & press the "OK" button
Press the "Right Arrow" button until you display "3. Setup" & press "OK".
Press the "Right Arrow" button until you display "5. No of Rings" & press "OK"
Enter # of rings with numeric keypad & press "OK"
Display will briefly show "Programmed"
Press "User Tools/Counter" button to exit back to regular display
Ricoh Aficio 1018 photocopier
For the Aficio 1018. SC-320 is laser failure - the polygon mirror motor inside the laser has failed and needs replacing. You will need to contact your nearest service agent for repair.
For your RICOH Aficio 1013F - SC-551 is overheat in standby mode as far as I can tell. The circuitry that controls the fuser section ie manages the heat has problem. Unless its right near a source of heat like a heater or has no circulation around you machine you will need contact a repair agent for this machine also.
No blue copy
Hello rfaustin,
I understand your question and the possible reasons behind it. I have been a field engineer servicing copiers for over 20 years and the best answer I can give you is that your device does not have the ability to recognize one color over another. More recent models do but there are limitations there as well.Optical devices primarily look for the presence or absence of data (image) and especially with a black and white copier which because of customer needs have been refined to the point of being able to recognize and reproduce even the lightest lead pencil strokes. And your "digital" copier is one of the best at recognizing any image that is not pure white. You can "lighten" the exposure and minimize the blue as it will of course be naturally lighter than the rest of the black text of your document. I am sorry I could not "FIXYA" :-) but I hope I have helped you a little by providing the answer to your question. Be well. ..............SPINAL............
Ricoh Aficio 1075 - SMTP error message
To use the scan to email function on your copier you need some settings from your internet provider (email setting specifically). Go into Outlook options and get your SMTP server, user name and password.
On your copier you need to change under User tools, system setting and file transfer and put these settings in. As long as your machine is set up for scan to folder thats all you should need.
Won't always print the job
Yes, that is correct, the 1013f is in the same series as the 120.
You can install it as you were trying, or get the latest driver here: http://support.ricoh.com/bb/html/dr_ut_e/rc2/model/x12_13/x12_13en.htm#Microsoft%20Windows%20Vista
Ricoh 1018
possibly the process unit and if you look in through the right hand door you can see the drum ...or it could come from a worn out upper heat roller.
all the best
Ricoh fax/copy machine
Instructions for 1013F are as follows:
above the blue numeric keys 2/3 there is a button with a small box with 123 in it this takes you in and brings you out of the USER TOOLS MENU.
Press user tool button once...user menu on display
use right arrow key...press3x..Fax Feature..press ok
right arrow2x..ok
again right arrow2x.ok....DATE/TIME on disply .ok
change then ok it once done exit by the 1st button you started with...USER TOOL BUTTON. all the best....
Saying load paper
Actually, you probably do not need a service person.
1. Turn machine off.
2. Remove toner assembly, not just bottle.
3. Unplug wire, and remove PCU. (right door must be open)
4. Remove the paper tray.
5 Turn the machine on its side.
You will be able to see, that it just snaps into place. Most likely one of the tabs broke off, but you can put a drop of super glue on it, and it will be fine. Make sure it has free up/down movement when installed before you glue it.
Then, make sure your guides in your paper tray are in there tracks. That is the most probable cause of your problem.
Way around "load paper' error
no there isn't any way to override it you might try the bypass tray.It might work.you have to be very careful with installing and removeing the paper tray when you do get it fixed.
Text "ghosts" or shadows
Replace Drum or blade(if possible) will fix on most types of copiers/printers, or rarer it is cause of fuser.
Not finding what you are looking for?
