Sampo SME-34WHD5 34" TV - Answered Questions & Fixed issues
Code error
do a reset by going into your TV settings. You can also look in your booklet that came with the computer contacting sampo directly.
Have a 42" Sampo plazma
Hi,
Before we proceed, i would like to share few details. The life of plasma totally depends on the usage. For a normal user it is anywhere between 10 - 14 years. There are few people who have actually used it for even more years depending upon usage and care. However, as i have no idea whether you have sparingly used it or the condition, so i would take an average life span.So, as a normal user you are left with less than 4 years before you would see other parts worn out. These are made in such a way that they mostly require replacement than repair, so cost is always a factor before getting them repaired. There is a thumb rule - when the cost of the repair is more than half the amount of the product, buy a new one.If are experience in electronics, could read schematics and would be able keep precautions, then it's different - you could save labor cost. Unless it is better to replace it.
I am sure you must have checked all the connections to make sure there is no lose connection. As unplugging didn't help you, there could be few causes ranging from digital board, sustain boards and few more. The more probable cause is driver board failing. If you call a tech, it would be an expensive deal taking into consideration the cost of the new plasma TV's and age of the TV.
Note - As i cannot diagnose the TV, this information is purely based on what i saw on most occasions on the basis of the description you gave.
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
I HAVE A YELLOW POWER
You are saying that the TV has no display and no sound, right?
Is there any blinking red or green light?
Thank you!
I have a 42" Sampo-PME42S6
You can try a hard reset: Unplug TV from AC mains and remove all cables from TV. Wait about 30 minutes and replug to AC power and redo the cabling. Switch on the TV and see if it works.. this not work check the cable try yo use another pair of cables ,even this did solve your problem then you need contact the company if under warranty ,if its out of warranty then you need get service from local TV repair center....
Good luck..
Sampo DVE-611 apparently powers up
After several power ups, the front panel buttons eventually "woke up". Replaced remote, and everything's working fine. Not sure why the front panel was temporarily unresponsive.
How to remove child lock from BELTEK TV?
general steps:
Get the TV remote control and push the "Menu" button and select "Options".
Select "Child Lock" from the "Options" list. On some televisions, the "Child Lock" is named "V-chip".
Choose the "Remove Child Lock" selection. Highlight this and then hit the "Enter" button.
Enter the four-digit code that you used when you activated the child lock feature. If you cannot remember it, your only option to deactivate the child lock is to reset the TV. The instructions for resetting a TV is written on the user's manual of the TV.
Exit the TV menu once you have entered the four-digit code. To do this, press the "Exit" or "Menu" button on the TV's remote control.
If you don't have a remote, you might try leaving the TV unplugged overnight. Some TVs will 'forget' their settings if left without power for a long period. You could also potentially buy a cheaper universal remote, and use that to turn off the child lock.
4/22/2024 8:10:04 PM •
Televison &...
•
Answered
2 days ago
•
16 views
How to pairing Ruwido Amadeus R 9710 to tv?
To pair your Ruwido Amadeus R 9710 remote to your TV, you can follow these steps:
Insert Batteries: Your remote is powered by two 1.5 V AAA batteries1. Make sure to insert the batteries correctly.
Switch on your TV: Ensure your TV is turned on.
Press the TV key: Press the TV key on your remote control for approximately 4 seconds until the LED flashes twice.
Enter the Code: After seeing the 2 flashes and within 5 seconds, enter the 3-digit numerical code from the list provided with your remote2. After entering the code, the LED will flash twice indicating that the code has been accepted.
Test the Remote: Point the remote control towards your TV and press the key. If your TV does not respond by going into Stand-By mode then repeat steps 3 to 5 and enter the next code in the list.
Bed.-Anl. H2 Version1 (ruwido.com)
4/21/2024 7:58:23 PM •
Televison &...
•
Answered
3 days ago
•
14 views
Not finding what you are looking for?