Top 20 Sampo PME-42V3 42 in. Plasma Television Questions & Answers


I have a Gohanz sampo

Serial ports are not meant for video only data communications if it is VGA port then your fine but the red white and yellow RCA connections are what you should be using this cable can be picked up at any local radio shack or walmart pretty cheap. As for the computer if the tv has a vga port connect it by that these vga are also cheap and can be found at radio shack or staples.
5/4/2011 10:44:27 AM • Sampo PME-42V3... • 205 views • 0 helpful votes

Can i just hook up a dvd home entertainment

Hi, I am sure we can help, but please provide the system number and make so we can check for wiring schematic.
12/3/2010 1:56:29 AM • Sampo PME-42V3... • 109 views • 3 helpful votes

Whats dvi in rgb in

Digital Video In and Red Green Blue in?
12/12/2010 7:54:33 PM • Sampo PME-42V3... • 40 views • 0 helpful votes

Just clicks when powered on

Check for the power supply. Need to be replace.
11/1/2010 1:08:48 AM • Sampo PME-42V3... • 88 views • 0 helpful votes

Need universal remote control code for maxent 42" plasma tv?

I hope that you have gotten this resolved, but if not, or if you have any other questions, here are the codes and some simple steps to run through.

1. Hold down the clear TV button until all lights light up at the top of the remote
2. Punch in a 3 digit code (provided below)
3. Press the # (POUND) button
4. Try powering the tv on/off, and the volume. If one or more of these functions do not work, start over from step 1 with a different code


Becki Barned
DISH Network Customer Service
5/17/2010 5:57:10 AM • Sampo PME-42V3... • 1,299 views • 1 helpful votes

Please tell me about power supply problem and

The power supply for HDTV is the board where the AC plug goes into. It is a very sensitive circuitry that can be easily damaged. Under normal circumstance it is very reliable. This is how they work basically. The AC current is rectified (converted into DC). Then filtered by means of large capacitors. The DC Voltage ( about 180 DC volts from 120 AC) is supplied to power transistors (usually FET or field effect transistor). The Transistor are switched at high frequency( usually over 100KHZ or 100,000 times per second) Which drives the transformers to step down the voltage. When the TV is off there is a standby voltage which is on at all times, and it is typically 5V. This standby voltage is the first thing a technician check for when troubleshooting power supply problem. When the TV is turned on everything in the power supply comes to life supplying power to every circuit boards which are of diffrent voltages such 12V, 24V etc. HDTV power supplies are very complicated using the latest technology employing power saving chips that minimize power usage on standby mode. Explaining the it in great detail would require many pages but this is just the basic.
6/26/2010 7:35:32 AM • Sampo PME-42V3... • 172 views • 0 helpful votes

Will be watching tv and all of a sudden one of the

Definitely the Digital Board. You will have to take the number (s) off the board and do an INTERNET search for it. That's the only way for that make.
11/30/2009 10:25:21 PM • Sampo PME-42V3... • 219 views • 2 helpful votes

Unable to hook up my ''Dish'' cable to the TV

If the cable comes from the dish,then unless you have a freesat tv that will not connect into your tv.The cable from a dish normaly connects into a sky box or cable box.You need a cable from an aerial to connect into the tv.
11/11/2009 9:09:56 PM • Sampo PME-42V3... • 220 views • 0 helpful votes

Set child lock manually no remote now wont switch on

Here are the instructions for unlocking digilogic devices.

I hope that helps.
4/13/2009 9:02:00 PM • Sampo PME-42V3... • 433 views • 0 helpful votes

I need a power supply board for a Sampo TV Model PME 42V3

you can the required parts at just select the exact model number and exact brand and the required part will get listed.just select and order one for you.
1/14/2009 2:48:35 PM • Sampo PME-42V3... • 168 views • 0 helpful votes

Black Screen

Reuben. On the Power Supply PCB marked QPWB11326-1B-4 you'll find a Component marked,
TH701 just above the Fuse! Remove this component and bridge it out!
This should solve your problem! Contact me on [email protected]

Gavin Burger
7/23/2008 4:05:35 PM • Sampo PME-42V3... • 341 views • 0 helpful votes

Relay clicks then shuts off - no picture/ no osd

No picture
  1. Power cord disconnected.
  2. Power not switched on.
  3. Improperly connected signal cable.
  4. Monitor in power save mode.
  1. Connect power cord.
  2. Turn the power switch on.
  3. Connect the signal properly.
  4. Press any key on computer.
3/5/2008 11:28:45 PM • Sampo PME-42V3... • 246 views • 0 helpful votes

Got a 42 sampo plasma tc, no picture

Howzit Brother.

I had the same problem, but managed to repair it myself! There is no need to purchase a new
Power Supply! You can service the faulty PCB yourself, or give it to a Tehnician to service for you.
If you want to try service to yourself, here is how,

On the PCB marked QPWB11326-1B-4 you will need to do the following<

Replace the following Capacitor's, CS704(Most important one), CS705, CS706, CS707, CS708, CS713, CS715.
Replace the TOP210PFI IC marked ICS02
Replace the PC123 OPTO marked ICS03
Replace the TL431 Shunt Regulator marked ICS04

This solution should work! email me on [email protected] if you have any other requests!

Gavin Burger.
6/12/2007 9:35:43 AM • Sampo PME-42V3... • 760 views • 1 helpful votes

Manual for samsung un46es6500f

3/22/2012 11:45:51 PM • Sampo Televison... • 108 views • 0 helpful votes

Tv wont turn on

You need troubleshooting to find the cause of the problem first. It can be simple or complicate problems.
Please read my guide.
Please see my basic troubleshooting guide here: Failed TV and Monitors: Learn about bad caps: Parts: Capacitors kit: he can make you a set of caps. Or just make sure to use caps with low ESR, 105c rating such as PANASONIC FM or FC series. Please post back what you find.
12/1/2010 8:12:52 PM • Sampo Televison... • 163 views • 0 helpful votes

Have a 42" Sampo plazma


Before we proceed, i would like to share few details. The life of plasma totally depends on the usage. For a normal user it is anywhere between 10 - 14 years. There are few people who have actually used it for even more years depending upon usage and care. However, as i have no idea whether you have sparingly used it or the condition, so i would take an average life span.So, as a normal user you are left with less than 4 years before you would see other parts worn out. These are made in such a way that they mostly require replacement than repair, so cost is always a factor before getting them repaired. There is a thumb rule - when the cost of the repair is more than half the amount of the product, buy a new one.If are experience in electronics, could read schematics and would be able keep precautions, then it's different - you could save labor cost. Unless it is better to replace it.

I am sure you must have checked all the connections to make sure there is no lose connection. As unplugging didn't help you, there could be few causes ranging from digital board, sustain boards and few more. The more probable cause is driver board failing. If you call a tech, it would be an expensive deal taking into consideration the cost of the new plasma TV's and age of the TV.

Note - As i cannot diagnose the TV, this information is purely based on what i saw on most occasions on the basis of the description you gave.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!
9/23/2010 1:59:18 AM • Sampo Televison... • 155 views • 0 helpful votes

Code error

do a reset by going into your TV settings. You can also look in your booklet that came with the computer contacting sampo directly.
3/16/2010 4:08:20 AM • Sampo Televison... • 93 views • 1 helpful votes


You are saying that the TV has no display and no sound, right?

Is there any blinking red or green light?

Thank you!
3/5/2010 9:05:55 PM • Sampo Televison... • 91 views • 0 helpful votes

I lost the remote and I cant find a universal

You can order origional remote from the factor for $10.
I also recommend checking ebay.Sampo Rl-611 Dvd Remote Control $19.95 - eBay
6/23/2009 4:40:23 PM • Sampo Televison... • 137 views • 1 helpful votes
Not finding what you are looking for?
Sampo PME-42V3 42 in. Plasma Television Logo

32 questions posted

Ask a Question

Usually answered in minutes!

Top Sampo Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76851 Answers

Jaime Hernandez

Level 3 Expert

2351 Answers


Level 3 Expert

85240 Answers

Are you a Sampo Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sampo Televison & Video

  • Sampo Televison & Video

Most Popular Question

need universal remote control code

  • Televison & Video