SVA-USA EV-1703 17 in. LCD Television - Answered Questions & Fixed issues
SVA EV-1703 Manual
You can use a laptop charger, as long as the connecter to the TV fits it'll work. I'm using one for my old set. I bought it from the Salvation Army for $5 without a power cord.
Hope this helps!
Picture goes out after 2 seconds
Tv have picture only few sec.than dies have sound left only?Yes,than the tv long board call the LCD inverter board is dead.This long LCD inverter board help the LCD screen panel to have a backlight to produced a picture.Tries websites like Shopjimmy.com,Ebay.com to buy this long LCD inverter board for the replacement.
The power went out and having trouble getting tvto
This is the best solution for your problem as a 40 year experience with wires etc.
Go to the source of your cable signal connector .
Open it and clean the terminals with emery paper , sand the end of the cable shiny clean from corrosion , get a new barrel connectors with gold terminals if possible lengthen the ends of the cable , insert and tighten good, use thick rg-16 or rg 40 cable with good insulation ends crimped professionally with a crimpier or buy ready made , not from dollar store. Get a gold plated professional splitter if you need one or two , it will cost about 15 or more each . Make the cable runs as short as possible, using the thick good cables. If needed get a signal magnifier. From radio shack or the source etc. Connect them good and tight . Ground the splitters . Problem solved , you will get crystal clear channel 2 to 7 including 3 and 4 . Isolate the TV cable from other cables and power wires.
Vitally
SVA television. Have model # EV1703 Remote no
When you say the remote doesn't get the channels I have to assume the channel entry behavior changed. I am not to familiar with this brand but these are the basics for most tv's. If you have not removed the cable input to the tv or unhooked anything before the problem started here are a few thing you could try. Push the menu or setup button on the remote and under the channel or setup option on the tv make sure it is set to Cable and not Air or Antenna. Run the tv through the auto channel search to reprogram the cable channels. This process can take close to 1 hour on some tv's since it has to scan through the digital and analogue tuners. This will allow your tv to add the correct cable channels and remove the unwanted ones. You should be able to enter the channel number or move up and down with the channel buttons on your remote.
Only get a few channels
try these people as i hear they are good. The Office of Research Services at The University of Georgia
P. O. Box 2187 ? Athens, GA 30612 ? Phone: 706-542-2411
We understand that your problem
some universal remotes are used only tv play.they did not open menu .so you bought original remote and solve your problem. thank you.
10/11/2010 8:06:53 PM •
SVA-USA...
•
Answered
on Oct 11, 2010
•
181 views
Remote replacement for craig cht904
It will be very difficult to get a universal remote control for this device. The only way to get its remote is, to contact the authorized service center for Craig at your town. I've searched for codes over 1200 remote manuals, but can't find a remote control which has setup code with this device.
2/7/2023 6:11:54 PM •
Televison &...
•
Answered
35 minutes ago
•
707 views
My Openview Decoder not showing any indicator if plugged in on power supply. What might be the problem please?
The power supply inside it has likely failed. Remove the mains plug for 5 minutes. Hold power button for one minute. Plug it back in. If that doesn't reset it, get the maker to replace it for a new one.
Openview Decoder Only
https://www.openview.co.za > get-openview > openvie...
You can enjoy local and international shows, including blockbuster movies, drama, series, kids' entertainment, reality, sports, music, Bollywood, as well as ...
Can i connect my tv with a phone via cable to watch movies?
Mobile High-Definition Link (MHL) is a common way of connecting an Android phone to an HDMI TV with a micro-USB cable. It is possible to use this method for all MHL-compatible devices. MHL is one of the most common solutions for connecting a phone to an HDMI TV with a micro-USB cable.
2/7/2023 4:41:52 PM •
Televison &...
•
Answered
2 hours ago
•
17 views
Redi remote control manual for an genessis g506 for sound system
Redi remote control manual for an genessis g506 for sound systemGENESIS G506 REMOTE CONTROL MANUAL1. Battery InstallationThe GENESIS G506 remote control requires two AAA batteries. To install the batteries:a. Remove the battery compartment cover by pressing the release tab on the back of the remote.b. Insert two AAA batteries into the battery compartment with the correct polarity.c. Replace the battery compartment cover.2. Setting Up the RemoteOnce the batteries are installed, you will need to set up the remote for use.a. Press and hold the MODE button for 3 seconds to enter setup mode. The red LED will flash twice.b. Press and release the DEVICE button to select the device you want to control. The LED will flash once for each press.c. When the desired device is selected, press and hold the MODE button for 3 seconds to save the selection. The red LED will flash twice.d. Repeat steps a-c for each device you wish to control.3. Using the RemoteOnce the remote is set up, you can use it to control your devices.a. Press the DEVICE button
2/7/2023 9:07:54 AM •
Televison &...
•
Answered
10 hours ago
•
19 views
TCL 43S425CA - stuck on set up loop. Do I need a board replacement of any kind?
If your TCL 43S425CA TV is stuck in a setup loop, it is likely an issue with the software or firmware of the TV. Here are a few things you can try before considering a board replacement:
- Power cycle the TV: Unplug the TV from the power source, wait for a minute, then plug it back in and turn it on.
- Update the software: Check if there is an available software update for your TV. If so, update the software following the instructions provided by the manufacturer.
- Factory reset: If the power cycling and software update do not resolve the issue, you can try a factory reset. This will erase all of your settings and return the TV to its original state. Check the manual for instructions on how to perform a factory reset.
- Contact the manufacturer: If the issue persists, it may be a hardware problem and you may need to contact the manufacturer for a repair or replacement.
Note: It's always best to check the manufacturer's website or manual for the latest troubleshooting information and support options. Before you decide to replace any board, make sure that you have a warranty for the TV or if it's an old one, then it may not be cost-effective to get it repaired.
Where is the 5 amp fuse providing 12 power to the display on thetford fridges
The 5-amp fuse that provides 12V power to the display on your Thetford N180 fridge is most likely located in the main fuse box. Some Thetford fridges have a separate fuse specifically for the display, but others use the main fuse for power to the display and other components.
I would recommend checking the main fuse box again to make sure that the appropriate fuse is in place and that it is not blown. If it is in place and not blown, you can check the wiring leading to the display to ensure that there are no loose connections or damage to the wires.
If the fuse and wiring are fine, the issue may be with the display itself and it may need to be replaced. If you are not confident in troubleshooting the issue, it is recommended to seek assistance from a qualified technician.
Not finding what you are looking for?
