Hayward SP3015X20AZ 2 HP SUPER PUMP II SP3015X20AZ - Answered Questions & Fixed issues


Sounds like the thermal protector for the motor is tripping. This means there is a problem with the motor overheating.
It is a self resetting switch so when it cools off enough the pump will come back on. It also means you probably need a new pump.

Hayward... | Answered on Feb 10, 2018 | 88 views


Friend had similar problem... Clean filter, added earth, primed pump and sound went away and had great flow... If not, possible impeller problem..

Hayward... | Answered on Jul 15, 2011 | 211 views


let the air out of the filter as you try to start, this makes it hard for the pump to pick up the water. i would check the impeller and shaft seal,and basket for cracks, if the basket is cracked 99% of the time the impeller is plugged ..shaft seal there is is one one ebay with how 2 for around 10 bucks SMART ! PRIME the pump after a repair !!

Hayward... | Answered on Jun 07, 2011 | 122 views


You will have to change the power on your breaker ... take the white off and put it to the neutral bus. This will change the power beig delivered to the pump. In the motor, remove the white wire and put it on L1 ... black should already be on L1.

A side note ... 220 runs more efficiently and your motor will run cooler and at less expense. I suggest you not change it unless there is good reason.

Hayward... | Answered on Jun 05, 2010 | 88 views


Could the Error code be HS? That is high temperature limit. Perhaps you' don't have enough flow, allowing the heater to heat the water to a temperature higher, than the thermostat setting. Make sure your bypass valve is closed, allowing full flow through the heater. Check your filter pressure differential , and skimmer baskets.
You didn't give your model number, and there are many models. You can go the Hayward website below and select your exact model number and download the manual. The manual will explain each error code.
http://www.haywardnet.com/inground/products/manuals.cfm

Hayward Pool &... | Answered on Jun 07, 2020 | 12,395 views


Are you sure it has a centrifugal switch?
Capacitor start/ capacitor run have been the standard for a good number of years.

Hayward Pool &... | Answered on Oct 26, 2019 | 302 views


Hayward's website has manuals for all their products.

Hayward Pool &... | Answered on Oct 26, 2019 | 122 views


The 24v is called the secondary and sometimes called the out-put. Make sure you have 240v on the primary, sometimes referred to as the in-put. If you have primary voltage then you should have secondary voltage, if not then replace transformer. Make sure the secondary, 24v control fuse is the correct size and present. If the secondary is shorting together or to ground somewhere, it will cause damage to the transformer.

Hayward Pool &... | Answered on Aug 18, 2019 | 130 views


Call a qualified electrician. More information would be needed to accurately trouble shoot your issue. Do you have automation connected to your heater? Is the heater trying to fire when the pump is off or is it ONLY the fan?
Try disconnecting your Water Pressure switch on the heater and see if the issue stops. With WP switch disconnected the heater should not work and the fan should stay off. Replace WP switch and see what happens.
Call a QUALIFIED electrician.

Hayward Pool &... | Answered on Aug 12, 2019 | 130 views


Check for proper supply voltage and that the impeller moves freely. If these are good then likely a bad capacitor.

Hayward Pool &... | Answered on Jul 30, 2019 | 132 views


the prologic control unit will not offer programming for what you seek. the most detailed timers will offer weekday or weekend for each pump speed. you may want to get a remote system so you can control functions from your smartphone

Hayward Pool &... | Answered on Jul 26, 2019 | 129 views


try filling your hose by holding it in front of the return jet. once filled, hook the hose up as normal

Hayward Pool &... | Answered on Jul 26, 2019 | 159 views


this is a common issue. there is a componant on the circuit board called a voltage limiter. when there are power surges (by hydro company or by using a timer), this capacitor takes the surge to protect the circuit board. in your case, the limiter has blown.
you can either replace the circuit board or find someone to remove the limiter and solder in a new one. (its the round black disc to the right of the front display toward the top) in most cases, you will see a hairline crack in the casing or it may have exploded completely. i usually tap it with a screw driver to show customers the damage. FYI: i usually replace about 50 a year and never had one fail

Hayward Pool &... | Answered on Jul 26, 2019 | 134 views


the rinse setting only cleans out the dirty water in freeboard and pushes sand to pack it. just about impossible for it to not work. if there is water coming out the discharge, you are golden.

Hayward Pool &... | Answered on Jul 26, 2019 | 127 views

Not finding what you are looking for?
Hayward SP3015X20AZ 2 HP SUPER PUMP II  SP3015X20AZ Logo

4 questions posted

Ask a Question

Usually answered in minutes!

Top Hayward Pool & Spa Experts

john h

Level 3 Expert

23504 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Paul Carew

Level 3 Expert

3527 Answers

Are you a Hayward Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...