Weiser Lock GED1460X GED1460X26D Satin Chrome PowerBolt Powerbolt Touchpad - Answered Questions & Fixed issues
On my house door lock, I recharged my batterie and now the lock wont work
When it comes to rechargeable batteries there is an unspoken rule to not use them for smoke detectors, clocks, and menial electronics. Only use them for flashlights and stereo systems that you carry on your shoulder. :) All you can do is make sure that the batteries are touching all the terminals and that they are facing the right way.
8/25/2023 7:19:10 AM •
Weiser Lock...
•
Answered
on Aug 25, 2023
•
82 views
How do I enter new code?
www.
weiserlock.com/.../
electronics/smart...
Translate this page
Weiser Lock25605-02 Weiser SmartCode Manual. Program. Button .... Press and hold the "LOCK" button on the exterior keypad, while fully inserting the battery pack into .... anyone withaccess to the power board can change these codes, you must restrict access ...technical means, or evaded by entry elsewhere on the property. No lock.
11/26/2015 11:25:58 PM •
Weiser Lock...
•
Answered
on Nov 26, 2015
•
655 views
Dead bolt too stiff
If you mean it feels like it's dragging when extended, it probably need to the screws holding the inside portion of the lock to the outside portion and realign those two while actuating the lock to find where it operates freely.
1/31/2015 10:40:50 PM •
Weiser Lock...
•
Answered
on Jan 31, 2015
•
97 views
I installed a weiser smartcode lockset and the
2 important things which may seem dumb but solved my problem:
- Make sure that once everything is in place, you hold the lock button before inserting battery pack (and keep holding the lock button) until you hear 2 beeps. The latch should come and go.
- Last but not least, make sure you put NEW batteries in... I had old batteries and when i tried it seemed like is was working but could not finish the door direction finding sequence stated above. Make sure they are new and it should work!
7/21/2015 4:37:24 AM •
Weiser Lock...
•
Answered
on Jul 21, 2015
•
4,737 views
Key pad will not work at all
soak the lock in a container of 90% isopropyl alcohol you can get this at a drugstore for about a dollar a pint then let dry in the sun.I take these apart and spray the parts with alcohol but only try this if you think you can put the lock back together again correctly
11/18/2013 6:05:26 AM •
Weiser Lock...
•
Answered
on Nov 18, 2013
•
80 views
I need to reprogram the
First, push the program button on the power board once. Enter the four to eight
digit code by pressing the numbers on the outer touch pad. Press the lock button on the
lock button on the touch pad to set the code. You will hear a two second long beep when
your code is accepted. If the unit does not beep, too much time has elapsed between pressing
the program button and entering the code. Repeat the programming sequence. Enter your number
to check that it works.
7/27/2011 9:05:51 PM •
Weiser Lock...
•
Answered
on Jul 27, 2011
•
246 views
How to remove covere to
Here's a link which tells you how to remove the cover, and reprogram the lock codes:
http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx
3/12/2011 11:25:14 PM •
Weiser Lock...
•
Answered
on Mar 12, 2011
•
191 views
The lock button in the
I have installed your Powerbolt, but when I push the Lock Button, it unlocks? What should I do?
First remove the cover on the inside of the Powerbolt
unit. On the right hand side under the batteries, you will notice that
is says "Door Direction Jumper". If the cap is mounted on Prongs 1 &
2, carefully remove it and move it over so that it mounts Prongs 2
& 3. A is right handed, B is left handed.
3/6/2011 10:41:31 PM •
Weiser Lock...
•
Answered
on Mar 06, 2011
•
201 views
I need to change the combination
Here's a link which tells you how to remove the cover, and reprogram the lock codes:
http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx
3/5/2011 11:09:42 PM •
Weiser Lock...
•
Answered
on Mar 05, 2011
•
63 views
How do you reset the mastercode in the WeiserLock
Here's a link to the Frequently Asked Questions page for the Powerbolt 1000:
http://www.weiserlock.com/Support/Faq/50160000000HhhZAAS.aspx
The instructions for reprogramming the code can be found there. Good luck!!
3/26/2011 3:43:42 AM •
Weiser Lock...
•
Answered
on Mar 26, 2011
•
561 views
Not finding what you are looking for?