20 Most Recent Diamond Products 01738 Core Bore Weka DK12 Drill Motor - Page 6 Questions & Answers

Contact Steel Craft or its distributor to inquire.

Cobalt bits are an upgrade from HSS because of 5-8% Cobalt in an alloy they work good in drilling in hardened or stainless steel. Carbide drill bits are tough too, but they are the most brittle bits. Carbide-tipped tools are usually used in masonry and stone. Full-body carbide bits are usually used in automated production only. Solid carbide drill bit So, actually, the answer to your question is to buy a cobalt bits.

The humming motor is that it could not get a turn direction because of only ac and a bad centrifugal or start capacitor if it hums try to turn it clockwise on the chuck to see if it will run .

No parts seem to be available. You would have to have one made in a machine shop. It appears that is was a hardware store brand. https://www.google.com/search?q=Cal+Hawk+model+240-2127+parts ..

Sounds about right!

hi jason try going to a car fan belt specialist ,, one that stocks many sizes..take your old ones in to match them with.. as an example search on line as i don't know where you are i can not give more specific info on location.. as an example this web site http://www.totalrubber.com.au/ or try repco car spare parts Rubber Hose PVC Hose Rubber Matting i assume your belt is an "A" size regards pete

Try fleabay.

if you try to fix it you could void the warranty

https://www.youtube.com/watch?v=QmjfZ64LApE go and watch

Contact Northern directly to inquire.

really??

possible bad switch

Available here https://www.amazon.ca/s?k=ryobi+p102+battery&gclid=Cj0KCQiAifz-BRDjARIsAEElyGJ30Vv06S9XfGdN4F3lCUk6ew2MUOZaFEdfHoayx-9pVxZh3myToeAaAtDxEALw_wcB&hvadid=249769096490&hvdev=c&hvlocphy=9000809&hvnetw=g&hvqmt=e&hvrand=11753836365116415444&hvtargid=kwd-366019119797&hydadcr=25352_10276036&tag=googcana-20&ref=pd_sl_8tnky76zbd_e Videos here on replacing the internal cells https://www.google.com/search?q=ryobi+P102+battery ..

They usually smart chargers so once fully charged they revert to a trickle charge to keep them full.

Safest is to read the manual if you have one or download one if you haven't. You need to know the meaning of the flashing lights. If it turns out it means the battery is faulty - I have known battery chargers to refuse to charge a battery that has been fully discharged and after I had taken the battery to pieces and got some charge into the cells by diverse means it went on for another year or two. It is best to use and charge even if it has only a few minutes discharge. Top up charges don't heat the cells like a full charge does and it is the heat that shortens battery life.

Forward/reverse slider failure?

1. Defective batteries 2. Defective charger

Request the wiring diagram for model DR330 directly from B&D.

You are facing a puzzle many owners of cordless tools face - often! It could be either - unless you have a friend or neighbour or a nearby supplier that has the same model charger or battery to allow some swapping around. The charger I have seen looks like an old ni-cad type charger rather than a modern lithium type. Ni-cad batteries self discharge and if allowed to become discharged through lack of use they soon become useless if not quickly recharged. Generally ni-cad batteries should be checked and recharged if necessary each month. Young batteries shouldn't need charging much during storage but the older they become the more they will self discharge until they are useless. Only you know the history of the battery you want to recharge. The one hour fast charger has a certain amount of intelligence and safety built in and if working correctly will reject batteries it thinks will be unsafe to charge. If the battery will dismantle easily you could check each of the six cells with a voltmeter. If one or two are completely dead while the others have voltage it suggests the battery is past it...

Beware there Is no fuse inside for repairing used only for fire safety used, on marketing technical base there are no wiring diagrams beware of ordering a separate print of the charger can often be more expensive than a whole new charger and also look first for the option on warranty. powercord problems can a problem but the li-ion chargers are build up mostly with smd components and if damaged there is no support to repair for novice to refurbish.