20 Most Recent Stihl Ts 510 760 Cut Off Saw Repair Manual - Page 5 Questions & Answers

0 Answers

Why does concrete saw run for a minute or two, then shut off?

Stihl Saws | Posted on Oct 02, 2015 | Be the first to answer

0 Answers

What would cause stihl ts500i cutoff saw t o die when accelerating

Stihl Saws | Posted on Feb 23, 2015 | Be the first to answer

1 Answer

Gas spits out exhaust

poss carb problem change carb

Stihl Saws | Answered on Nov 29, 2014

1 Answer

How to adjust the carburettor on ts410

on the side you will see 3 holes one with a h and one with a l on the letter with a L screw it in fully then un screw one and a half turns on the letter that says H screw fully in then unscrew it back four turns

Stihl Saws | Answered on Nov 29, 2014

1 Answer

Stihl ts400 doesn t turn off

stop switch damage

Stihl Saws | Answered on Nov 29, 2014

1 Answer

Ts 500i has no spark

poss magnito

Stihl Saws | Answered on Nov 29, 2014

1 Answer

Stihl concrete saw looses power

poss draging in air, or carb problem

Stihl Saws | Answered on Nov 29, 2014

1 Answer

Trouble starting and running stihl 400 cutof saw

First clean or replace the air filter. If the fuel in the tank is more than 2 months old dump it out and put in fresh fuel. Clean or replace the spark plug.

Stihl Saws | Answered on Sep 29, 2014

1 Answer

I have a stihl ts-410 cut off saw. it will start and idle but when i squeeze the throttle it dies. how do i adjust the carb?

if this machine ran ok before this problem,and no one has adjusted the carb,then i would check the crank seals.i have just had this problem.and it was the seal on the puller side,though i replaced both whilst i was at it.hope this helps my freind.

Stihl Saws | Answered on Jan 03, 2014

1 Answer

My stihl saw ts400 start gran when cold but when you stop it and try to start it agin it wont start untill it cool's down and then it start ok

Clean the air filter and check that the choke is operating correctly.

Stihl Saws | Answered on Mar 04, 2013

2 Answers

Stihl ts 350 super cut saw died in the middle of cutting a brick

Can you get a compression tester to check the compression? With the throttle wide open, the choke OFF, and the decompression valve (if so equipped) NOT engage, pull the engine over 3-5 times or until the gauge quits rising. You would like to see 90psi or more and if it is at 60 or less then it is most likely a scored piston and cylinder or bad rings. If the compression is good you need to check for spark. If it has good spark then it will most likely be fuel related. Often a complete tear down and rebuild of the carb is what is required.

Stihl Saws | Answered on Sep 21, 2012

0 Answers

My stihl ts350 concrete saw has good spark and good fuel but not getting to the cylinder. it seems like good compression and the fuel is new and mixed properly. I take the plug out and it is dry and f

Stihl Saws | Posted on Sep 21, 2012 | Be the first to answer

0 Answers

My stihl ts350 is not getting fuel to the cylinder. carb is fine and there is fuel ?

Stihl Saws | Posted on Sep 21, 2012 | Be the first to answer

1 Answer

The cutter works but loses power at times

That could be caused by a number of things. A compression test would help narrow it down. You could also pull the muffler and visually inspect the piston and cylinder for any scoring. If you do a compression test look for 90psi or more. If around 60 or less then there is the problem for sure. Between that it still could be a scored or worn cylinder and piston or bad rings. Igniton and fuel issues could also be the problem so you need to do some trouble shooting to narrow it down.

Stihl Saws | Answered on Aug 25, 2012

1 Answer

FUEL LINE FOR THE TS 500

You will need to contact a Stihl dealer. Here is a link to the site where you can locate a dealer near you.

Stihl dealers

Stihl Saws | Answered on Aug 24, 2012

1 Answer

I rebuilt a TS400 and now it doesn't work, please help....

if you havent tuned the carbi try screw the low speed screw gently all the way clock wise onto the seat then turn it back 1 full turn anti clockwise.if then it starts turn the la screw clockwise till the blade starts to run then back it off till the cut disc stops turning a simple tune done

Stihl Saws | Answered on Aug 09, 2012

0 Answers

Stihl ts350 repair manual

Stihl Saws | Posted on Jul 05, 2012 | Be the first to answer

0 Answers

Stihl ts400 . The cutter works but loses power at times

Stihl Saws | Posted on Jun 21, 2012 | Be the first to answer

1 Answer

Hi, My stihl saw ts410 is really hard when i pull the starter coil, I have changed the cord and it seems as there is no compression could this be seized and if can i fix this myself and what would i n

It could be seized, or had dust throught the filter wearing the piston and rings, if this is the case it will be a new cylinder and piston required, it is possible to do it yourself if you have a good knowledge of mechanics.

Stihl Saws | Answered on Feb 18, 2012

1 Answer