Top 20 Bosch Dishwasher NTC Sensor 165281 - Page 5 Questions & Answers

Give details about the clock. Is it mechanical or electronic?

They are advertised as 50 foot range, but the accuracy starts falling off past about 35 feet

Hold the CLK button, and then the ADJ button. https://fccid.io/OWF-WSRX/Users-Manual/Users-Manual-171217

Hi, all electronic rotary laser levelers have an electronic calibration that you can do yourself, you just need to know the correct algorithm to control the buttons. Look here (https://laslev.com/reviews-laser-levels/firecore/automatic-rotary-laser-level-firecore-fre207r-servo/) for an example of this unit, it describes the entire calibration algorithm for the X-axis and the Y-axis. The buttons may be slightly different, but the principle is the same, I'm sure you can do it, there's nothing complicated there.

Have you changed the batteries in the outdoor temperature sensor?

Battery compartment contains reset button. Press. Will need to re-enter time and date. https://www.acurite.com/kbase/weather-stations/02031RM_Weather_Station.html

Place your remote temperature sensor and the inside unit together for about an hour to see if they both read the same or if there is a large difference in the temperatures.Dashes on the outside temperature reading may indicate that the inside unit is not receiving a signal from the remote. Change the batteries on the remote or change the location of the inside and/or outside units so that they can receive a strong signal between each other.Your smartphone temperature may be coming from a location that is not near your home. They are often from a weather service. Where is your local temperature sensor located? Is it in the sun? Is it on the south side of the house, or another location where the sun or an air conditioner or other heat source may affect the accuracy of the reading? Try to locate your outside sensor in a shaded location with plenty of ventilation, and away from heat sources.

Radio Frequency communication may come and go occasionally. This can be normal in some environments (e.g. moister climates). If transmitter signal is lost, please wait 2-4 hours for the signal to reconnect on its own. Here is a link to the User Manual for your product. https://www.lacrossetechnology.com/media/catalog/product/w/s/ws-8119u-it__faqs_1.pdf

search for it at this link...https://www.manualslib.com/3/331nc.html

no info -generic answer check with manufacturer -owners manual online search uging make and model of mystery unit

try new test leads first. even if the unit is miscalibrated, you should get the same measurements from the same components/circuits. you'll need to send the unit to a calibration center, or the manufacturer, to get it zeroed out, if you still need to afrer getting new test leads

Tape measure and manual for sale on eBay. https://www.ebay.com/i/113701075337?chn=ps

Not sure but if you press the clock button on the side; ? Press to start or stop a WWVB time signal search (which is what I think your clock is set to) ? Hold for 3 seconds to set time/calendar, etc.

Hello Anthony, I sent you a link so you can find out the manual of the tester Sperry DM-210a and another where you get an explanation of the operation I hope you can solve your concern Greetings Franco Dosil Hola Anthony, te envio un link para que puedas descrgar el manual del tester Sperry DM-210a y otro donde te dan una explicacion del funcionamiento Espero que puedas resolver tu inquietud Saludos Franco Dosil https://www.hunker.com/13414165/how-to-use-a-sperry-dm-210a-meter https://greenlee-cdn.ebizcdn.com/media/52058078REV01.pdf https://www.hunker.com/13407450/instructions-for-a-sperry-dm-210a

battery or internal damage

1. Disconnect the test leads from any energized circuit and then from the instrument. 2. Turn the range switch to the "OFF" position 3. Slide off the back case battery cover. 4. Remove the battery from the compartment and unsnap the battery connector. 5. Replace the battery with a 9V transistor type battery (NEDA # 1604), For maximum battery life, alkaline cells are recommended. 6. Reverse the above procedure to complete replacement.

I do not believe that you can buy these separately. They are factory programmed and paired together.

Have you tested the rain gauge using the calibration procedures on page 21 of the manual? Specifically confirming that the bucket is emptying about every 25 drops. https://www.acurite.com/media/manuals/01536-instructions.pdf

It's not clear what your question is.

If you select current measuring (A or mA) and have the test lead connected to V then you get this alarm. Same thing if you select Voltage measuring and the lead is connected to a current terminal. Check the connections and the selector setting.