20 Most Recent
Polaroid Polaview 211E Multimedia Projector - Page 6 Questions & Answers
I have an error code 033001 on my xp-345
The error code 033001 on an Epson XP-345 printer typically indicates a communication error between the printer and the computer. Here are a few steps you can try to resolve this issue:
- Check the USB cable connection: Make sure the USB cable is securely connected to both the printer and the computer. If the cable is damaged or frayed, replace it.
- Restart the printer and the computer: Turn off both the printer and the computer, wait for a few seconds, and then turn them back on.
- Update the printer driver: Go to the Epson website and download the latest driver for the XP-345 printer. Install the driver on your computer and see if the error code 033001 has been resolved.
- Uninstall and reinstall the printer: Remove the printer from the Devices and Printers list and then reinstall it.
If the above steps don't resolve the error code 033001, you may need to contact Epson support for further assistance.
How do i switch off Cleaning page print after each switch on HP lazerjet M551
To turn off the cleaning page print on your HP LaserJet M551 printer, you can try the following steps:
- Open the printer's Embedded Web Server (EWS) by entering the IP address of your printer into a web browser. The IP address can be found on the printer's control panel or by printing a network configuration page.
- Log in to the EWS using the default username and password (admin/admin).
- Click on the "Settings" tab, then select "Service" from the drop-down menu.
- In the "Service" section, click on "Service Pages."
- In the "Service Pages" section, uncheck the box next to "Print after each manual duplex".
- Click "Apply" to save the changes.
- Close the EWS and test the printer to confirm that the cleaning page is no longer printed after each switch.
Note: The steps mentioned above may vary slightly depending on the printer's firmware version. If you're unable to access the EWS or if the steps don't work, you may want to consult the printer's user manual or contact HP support for further assistance.
How to remove FRAC display on porpo YH-2000 calculator
To remove the fraction display on a Porpo YH-2000 calculator, you can follow these steps:
- Press the "Mode" button to access the calculator's settings.
- Use the arrow keys to navigate to the "Fraction" or "Frac" setting.
- Change the setting from "On" to "Off". This will remove the fraction display from the calculator's screen.
- Press the "Mode" button again to save the changes and exit the settings menu.
If these steps do not work, it's possible that your calculator model is different or that it has a different method of changing the fraction display. In this case, you may want to consult the manual or manufacturer's website for more information.
FDL 9640p uk. Start/pause key flashes every three-four seconds. machine wont start.
The flashing start/pause key on your FDL 9640p machine could indicate an error or a malfunction. Here are a few steps you can try to resolve the issue:
- Check the machine's power source: Make sure the machine is properly plugged in and the power source is functioning.
- Reset the machine: Unplug the machine for a few minutes, then plug it back in and see if it starts.
- Check for clogs: Look for any blockages in the machine's pipes, hoses, or filters that could be preventing it from functioning properly.
- Contact the manufacturer: If the machine still won't start after trying these steps, you may need to contact the manufacturer for further assistance. They may be able to provide more specific troubleshooting advice or arrange for a repair.
If the issue persists, it may be best to seek professional repair services to have the machine fixed.
Cl-100 topcon lenso meter initial error problem always comeback when I fix.. pls help how to solve for this
The CL-100 Topcon Lenso meter is a surveying instrument used for measuring distances and angles. An "Initial Error" message can indicate a number of different issues, including:
- Calibration Issues: Check that the instrument has been calibrated properly and the calibration values are within the acceptable range.
- Software Issues: Update the software on the instrument to the latest version, which may resolve any bugs causing the error.
- Hardware Issues: Check the instrument's hardware components, such as the battery, for any signs of damage or wear and replace if necessary.
- Settings Issues: Make sure that the instrument's settings are set correctly and adjust them if needed.
- Environmental Factors: Environmental factors, such as temperature and humidity, can affect the performance of the instrument. Make sure that the instrument is being used within the recommended temperature and humidity range.
If the "Initial Error" message continues to persist, it is recommended that you seek assistance from a qualified Topcon technician or authorized service center. They can diagnose and repair the issue and restore the instrument to full functionality.
How to fix cycle power and clean lower and imaging guide on i5200 scanner
If your i5200 scanner is not functioning properly, you may need to cycle power and clean the lower imaging guide. To do this, first power off the scanner and unplug it from the wall. Then, use a soft cloth or cotton swab to clean the lower imaging guide. Once the guide is clean, plug the scanner back in and power it on. If this does not resolve the issue, then you may need to contact a qualified technician who can inspect the scanner and make the necessary repairs.
I have a running business if I am going to start
Depending on how big your company is going to be.
I started with 250.00
One important bit of advice if you make it a limited company, if the company fails, all financial issues stop with the company. I Personally purchased high cost items, ie Van, tools etc. And created a financial agreement for my company to pay me back as and when my company could afford it. And like all financial agreements, the van, tools would not belong to the company until the last and final payment was made.
How do I get OUT of my carrot key on my graphing calculator
Maybe the carrot or caret cursor can be cleared on a TI
like
When the calculator is in Alpha mode, the blinking square cursor symbol is replaced with the reversed-A symbol. This symbol indicates that the next key you press will insert the green letter above that key. To take the calculator out of Alpha mode, press [ALPHA].
I have riso cv3230 machine
Error code T12-305 in a Riso CV3230 duplicator/printer typically indicates a problem with the control board. The control board is responsible for managing the various functions of the duplicator/printer, including temperature control.
There could be several reasons why the control board is generating this error code, including a faulty thermistor, a problem with the wiring, or a problem with the control board itself.
If you receive this error code, it is recommended to seek the assistance of a professional repair service to diagnose and resolve the issue. Attempting to repair the duplicator/printer yourself could result in further damage or safety hazards.
Calculator not feeding paper model TI-5035II
If your TI-5035II calculator is not feeding paper, it is likely that the paper feed roller is not properly connected. Make sure that the paper feed roller is securely connected to the calculator and that the power switch is in the "on" position. If the problem persists, you may need to replace the paper feed roller or contact the manufacturer for assistance.
It turns on and 5 seconds later e4 code pops up
The "E4" error code on a T9200 Vision Fitness treadmill typically indicates a problem with the incline motor. This could be caused by a malfunctioning motor, a problem with the wiring or connections to the motor, or an issue with the incline sensor or control board.
Here are a few things you can try to troubleshoot the problem:
- Check the wiring and connections: Inspect the wiring and connections between the incline motor and the control board to make sure that they are securely connected and not damaged.
- Check the incline sensor: Make sure that the incline sensor is functioning properly and that it is not blocked or damaged.
- Check the control board: Make sure that the control board is functioning properly and that it is not damaged.
- Check the incline motor: Make sure that the incline motor is functioning properly and that it is not damaged.
It's important to follow the instructions carefully and if you have any doubts or difficulties, consult the treadmill's user manual or contact Vision Fitness customer service for assistance. It's also important to note that it is recommended to have a professional technician to perform this task as it may cause other issues if not done properly.
HOW CAN I GET MY CALCULATOR TO TURN ON?
Depends on what the MYSTERY calculator is!!
Some have a switch on them. Some start up when you press the Clear button or even expose the solar cell to light.
Google
make model manual
All questions need 'make model (what it is)', first three words.
Not finding what you are looking for?
