20 Most Recent Onkyo TA-RW244 Single Cassette Deck - Page 7 Questions & Answers

“HT-R340 DSP Debug Mode” Does it show DSP ??????? Place a photo here to show more detail if you want.

“my onkyo TX902 keeps turning off by itself.” Amp Volume too large. Tune it down and also tune the speaker level down found in speaker config.

Hello Scott, to be able to guide you, in wiring so that you can have everything in your home theater system, you should comment that equpos you have I can suggest a generic connection to have the sound of each source in Tu Onkyo You have to connect the equipment that has HDMI output, in the corresponding entries in your Onkyo, accounts with only three inputs, if you have more than three equipment with HDMI, you can connect it to an HDMI input on the TV If you have other equipment that does not have an HDMI output, you should connect it to the remaining inputs of the Onkyo, according to its type Then, you connect an HDMI-HDMI cable from the HDMI output of the Onkyo, to the HDMI 1 input, of the TuTV Insignia And you also have to have a Fiber Optic cable, connected from the digital audio output of the TV (it is located on the side panel of connections) to the Fiber Optic input (Digital In) n ° 1 of the Onkyo, this connection allows you to listen to the sound on the Onkyo of everything you are looking for on the Internet, eg Netflix, YouTube, etc. In this way you would already have everything connected in the Onkio and you could enjoy the sound of the Home Cinema System I hope you manage to interconnect everything and you can enjoy a good sound and an excellent image I send you the links of the user manuals of TV Insignia and Onkyo, in case you need more information Greetings Franco Dosil Hola Scott, para poder guiarte, en cableado para que puedas tener todo en tu sistema de cine en casa, deberias comentar que equipos tienes te puedo sugerir una conexi?n gen?rica para tener el sonido de cada fuente en Tu Onkyo Tienes que conectar los equipos que tengan salida HDMI, en las entradas correspondientes en tu Onkyo, cuentas solamente con tres entradas, si tienes mas de tres equipos con HDMI, puedes conectarlo a una entrada de HDMI en el televisor Si tienes otros equipos que no tengan salida HDMI, los deber?s conectar en las entradas restantes del Onkyo, de a cuerdo a su tipo Luego, conectas un cable HDMI-HDMI desde la salida HDMI del Onkyo, hasta la entrada HDMI 1, del tu TV Insignia Y tambi?n tienes que tener un cable de Fibra ?ptica, conectado desde la salida de audio digital del televisor (se encuentra en el panel lateral de conexiones) hasta la entrada de Fibra ?ptica (Digital In) n°1 del Onkyo, esta conexi?n te permite escuchar el sonido en el Onkyo de todo lo que buscas en Internet, ejemplo Netflix, YouTube, etc De esta manera ya tendr?as conectado todo en el Onkyo y podr?s disfrutar del sonido del Sistema de Cine en Casa espero que logres interconectar todo y puedas disfrutar de un buen sonido y una excelente imagen Te env?o los link de los manuales de usuario del TV Insignia y del Onkyo, por si necesitas mas informacion Saludos Franco Dosil https://www.eu.onkyo.com/downloads/1/1/9/7/8/21637364_3342ba722d.pdf https://data2.manualslib.com/pdf4/98/9771/977072-insignia/ns40e560a11.pdf?5272bbc74f2dc78e6eb01f3f6deb2aec&take=binary

first of all, learn to use spellcheck.

just go to a mobile shop and tell them the problm they can fix it or just switch off and on it

Connect the line out terminals to the line input on your PC using a phono to stereo jack lead. Then use an audio recording program to record from the line input.

jmfnmfm

“quit working after a power surge.” Check voltage of speaker relay drive if there is +24V. If not, check +24V power supply. If OK,it must be either Main microprocessor unit, MPU or DSP problem.

3 seconds shut down: dc protection triggered. The problem comes from the vertically installed circuit board next to the heat sink with power transistors mount.

Maybe "Polk Audio PSW10 10’’ "&there’s no sound the standby light is red. Connect onkyo av-amp sub pre-out to line in and enter Onkyo av-amp speaker setting then subwoofer level calibration finally set +10db.

HDMI connections are fickle. I have similar problems with them, and have to find the right position of the HDMI plug itself before it will pass the signal. I pull up on it lightly or remove it and plug it in again. The point being, these connectors are not very reliable, and have to be fiddled with to get them to work.

does it have a VCR button? If so, hold the vcr button and press power - that is the standard reset for onlyo

The Onkyo TX-8255 does not support any internet or Bluetooth access directly. You may be able to use the Onkyo remote interactive (RI) dock, DS-A5, to get the wireless streaming, if you can find one on E-bay or a similar resale site. See https://www.onkyousa.com/Products/model.php?m=DS-A5&class=Accessory . Onkyo has discontinued manufacturing these docks. The dock connects to the receiver via an audio cable. The features and manual for the Onkyo TX-8255 are available at the product page on Crutchfield, https://www.crutchfield.com/S-Q75dK8s0iLY/p_580TX8255/Onkyo-TX-8255.html . The current link to the manual is https://pdf.crutchfieldonline.com/ImageBank/v20080824133600/Manuals/580/580TX8255.PDF . Unfortunately, if you can't find one of these docks, you'll need to connect use an audio cable between the TX-8255 and any dock for some gadgets or a direct connection for other internet connected devices. I wish that I had better news for you. Cindy Wells

No, wd40, "please" first try checking the solder connections, 9 times out of 10 it's bad solder connections. Not every issue with older Electronics is Cap related!!! Onkyo is super easy to repair like I mentioned earlier, check the solder connections first, also check the ribbons, unplug the clean the contacts with DeOxit5, if you still need help, don't hesitate to contact me, good luck!!!

"when first turned on, drops to tv, once reset, stays on cab/sat" Maybe the EEPROMused to STORE user information goes wrong.Check(1) voltage supplied to EEPROM +3.3V. at pin8(2)C226 47uf 16v(3)C225 10k nf(4)R256-257 4.7K (5)R260,R262 100ohms if they are correct.If correct, buy a reader to read the data stored in EEPROM and burn it to a new EEPROM. To locate IC203 CPU then find IC204: EEPROMsearch in taobao or google"Taobao USA/Hong kong/Tai Wan"then search"GZUT EZP_XPro V2 USB " will be cheaper <15USD. Maybe this can be used.https://world.taobao.com/item/559202211788.htm?_e_pi_=7%2CPAGE_ID10%2C8206437564

http://www.manuals365.com/swf/onkyo/sn29402478_ht-s3800_en_160425_web.html https://www.onkyousa.com/Downloads/manuals.php

Must be DSP problem no matter what model it is. TX-SR/NR OR even RZ Series.

(1)If old model TX-SR/NR, you should replace the BGA DSP Q3001 "D830K013A/BZKB" TO "D830K013DZKB"IF DZKB get damaged, replace it with same DSP Chip-DZKB.
(2)For Tx-SR series, the DSP Q201 TMS320D788E001B SHOULD BE replaced with same model.
(3)For new model, RZ series the DSP Q3404 CS49844 should be replaced with same model.
(4)Crystal marked X201/3001/3404 should be replacd.

If it has a preamp out use that.