Top 20
Energizer Eveready Utility Lantern Uses 6V Lantern Battery Questions & Answers
How do I get to the bulb?
Unscrew the head assembly. In the back of the assembly is a small plastic nut. Unscrew this and the bulb should fall out into your hand.
11/1/2014 3:15:43 PM •
Energizer...
•
839 views • 1 helpful votes
How to fix the switch on eveready lantern flashlight
The switch in the lantern is a press fit switch so you will destroy it when you remove it. Remove the lense and retainer ring. Remove the battery. With a pair of pliers, preferably channel lock water pump pliers crush the switch into small piece and discard. Trail Tech makes the exact water resistant switch model 040-ls-b and you can get it at Amazon or on eBay . The switch runs around $6.25 + $4.00 shipping
7/11/2014 12:55:13 AM •
Energizer...
•
1,725 views • 0 helpful votes
How to connect a spring pole 6v battery
Inside the case of the light, there will be 1 wire with a tapered notched connector. Take the connector with the low end of the taper and push it into the negative (-) spring (in between the coils ) of the battery. The spring will wedge the connector it one of the notches and will hold it securely. Reattach the lense carefully seating the end of the bulb onto the positive (+) spring of the battery.
5/25/2014 3:11:36 PM •
Energizer...
•
911 views • 0 helpful votes
How to test a flashlight bulb
To test a flashlight bulb you use an Ohm meter which will detect a broken filament or an open circuit within the bulb. If the bulb is bad it will read "OL" if it's good it will read "00.0"
6/14/2014 10:18:30 PM •
Energizer...
•
395 views • 0 helpful votes
Replacing a 6 volt battery
Check that the contacts where the springs on the battery make contact in the light to see if they are corroded. If so scrape or sand them off.
1/9/2013 10:13:56 PM •
Energizer...
•
1,163 views • 0 helpful votes
I have bought a new
The bezel (the circular portion on the front of the flashlight that holds the bulb and lens) will unscrew. The old battery should slide right out.
Hope this helps.
4/7/2011 11:50:00 PM •
Energizer...
•
1,537 views • 0 helpful votes
How do I change the
If it is the yellow floating lantern you have to remove the black plastic stub on the underside of the reflector using needlenose pliers to wiggle and slightly pull until it releases and the bulb will come out.
1/6/2011 7:09:25 PM •
Energizer...
•
9,194 views • 17 helpful votes
How to change lightbulb in hard case energizer flashlight?
Hello, Lori -
There is more than one style of Energizer Hard Case Flashlight.
- Professional Mult-Use Light
- Professional LED Task Light
- Spotlight
- Professional LED Inspection Light
- PivotPro Light
- LED Work Light
- LED Magnet Headlight
- Professional Rugged LED Headlight
Which one are you asking about?
Without knowing which model your question is about, I suggest you contact Energizer Customer Service and ask how to open your flashlight model to change the battery. This is the link to the Energizer Contact Us web page:
https://energizer.custhelp.com/
Best wishes.
7/1/2018 8:22:31 PM •
Energizer...
•
2,762 views • 0 helpful votes
Change the battery in the hard case
Start by unscrewing the lense cap retaining ring. Pinch and remove the clip from the negative (-) spring on the battery. Remove battery and slide new one in. Reconnect wire connector in between spring on the negative side of the battery. Note: some lanterns have a v'd plastic ear on the back of the reflector so when you go to screw the reflector back on, align the v'd ear with the plastic bar inside the case under the handle and slide it together until you can screw the retainer ring on.
2/28/2015 11:36:40 PM •
Energizer...
•
516 views • 0 helpful votes
Would like to know
That's the model number for the Eveready Rechargeable Torch, I think.
11/27/2010 3:07:55 PM •
Energizer...
•
683 views • 0 helpful votes
Not finding what you are looking for?