risk 371e is here
https://www.google.com/search?q=risk+371e
something not right. All question need 'make model (what it is) as first three words and then a clear question please.
..
1. Press Manual 1 Manual 2. Enter a frequency 3. Press E 4. Press Manual 5. Repeat steps 2, 3 and 4 as needed 6. When you finish the programming steps press Scan
All questions need full 'make model (what it is)'.
Posted to Office Equipment. Is this a Point of Sale Cash Register.
Answers can usually be found on Google but 'farex 04' doesn't show much, but there is an FM04?
https://www.google.com/search?q=farex+04+error+78
..
A two part temp , humid. monitor has base ( with LCD display, Integ Circuit, batteries) and sending unit ( with similar)
Start w best guesses -
sender 1 battery(s) low, 2 not make contact w plated spring, flat metal contacts which are "HARD TO SEE corroded slightly" from previous leaking battery, hard repair, sand off, solder, better to replace metal 3 signal path interference
Base- also 1 OR 2 OR 3 like sendr and 4 low chance, contacts to LCD display, to be cleaned w drop of soap/water/swab/alcohol
First press the reset button then when the display says "RESET OK ?" press the CAPS button then the button marked "2nd" (bottom left hand corner) then press Enter. Display will then say "BUSY". Reset is then complete.
Hassan. It is better to make your own Question than tagging it to one from 10 years ago!
P98-934 : communication error between MCTL PCB and RF PCB, on RF PCB side. Translation: the rf reader in the drum did not communicate with the mechanical control board. First try turning off the machine and back on. Second try resetting with holding the reset key while turning on the machine.
Jun 24, 2015
You could start with the phone directory enquiries, if that fails try a detective agency. If I have misunderstood and it is true love rather than truelove, fate will lend a helping hand but meet it half way and stop looking. It will then find you.
Hope that helps.
To convert from binary to decimal, we have to line up the numbers with the binary columns.
1 1 1 0 0 0
2^5 2^4 2^3 2^2 2^1 2^0
32 16 8 4 2 1
32 + 16 + 8 + 0 + 0+ 0 = 56
Good luck.
Paul
https://www.facebook.com/ConlogSolutions/posts/im-having-a-rf-con-error-cant-do-anything-on-the-gadget-please-help-on-how-to-re/962048393965724/
Quoting from South African link:
"Conlog Hi Ola-daniels, Please see below steps to assist with RFCON error :
* Press the Back arrow on the keypad - this step is to refresh the UIU ( the device)
* Type # 75 # - this is to check the signal strength
If it does not go back to the normal display
*Type # 80 # - this is to refresh the meter
Then lastly you can repair the meter and the UIU by # 36 #
The above steps will work better if you are outside the house because the meters uses the radio frequency connection
The above error will occur in instances of bad weather conditions or if there is load shedding or power failure
If the problem persists after trying the above you may contact the municipality or the service provider"
the binary system are made only for ones and zeros, when you try to "add one digit" in the binary system, you must add an 1 in the right-sided zero of the binary code, that means that when you want to count up in binary, it should be:
00000 = zero
00001 = one
00010 = two
00011 = three
00100 = four
00101 = five
and so on.
to go up to next number you must add a "1" in the place close more to the right, once this digit has reached its two states (binary= first 0 then 1) the same process occurs in the next digit , but it only rise from zero to one once the right one has reached its two binary states.
the binary digit 01101 stand for: 13 (decimal)
