20 Most Recent
Janome Sewist 525S Mechanical Sewing Machine - Page 3 Questions & Answers
Janome 350E suddenly stopped reading the USB
Your space is not formatted correctly to the size of the hoop. For example if the hoop is 5x7 your design has to fit within that space, and the space cannot be bigger than 5x7. Strange but true and it will fix the reboot and shut down issue.
I've been trying out a New Home, Janome 641 for my granddaughter. It will only sew backwards.
A new old machine for you I assume.For older mechanical only machines, reverse stitch is an exaggerated long stitch length that changes the angle and contact time of fabric to the feed dogs. Try setting stitch length to minimum and straight stitch. Check feed dog up/down is functional (if featured). It could also be the reverse linkage is simply stuck and the machine is in need of a thorough clean/lube.I looked for a manual but so far have not found. I'll append if I find.
Janome 5000 screen remeins black
It migHt just be the LCD screen controller. RotAting knob inside top front near bobbin winder bobbin holder. Rotate it gently as very sensitive
Janome Mystyle 22 skips stitches on the buttonhole function
If your Janome Mystyle 22 sewing machine is skipping stitches specifically when using the buttonhole function, there could be a few possible causes for this issue. Here are some troubleshooting steps you can try:
1. Needle: You mentioned that you have already changed the needle, but it's worth double-checking that you are using the correct needle type and size for the fabric you are working with. Ensure that the needle is inserted correctly and tightened securely.
2. Thread tension: Improper thread tension can cause skipped stitches. Make sure the upper thread and bobbin thread are properly threaded and that the tension settings are adjusted correctly for the fabric you are using. You may need to experiment with different tension settings to achieve the best results.
3. Buttonhole foot: Check that the buttonhole foot is attached securely and positioned correctly. Ensure that it is clean and free from any lint or debris that may be affecting its performance.
4. Feed dogs: The feed dogs underneath the fabric may not be gripping the fabric properly, especially when working with lighter fabrics. Ensure that the feed dogs are clean and free from any obstructions. You can try using a fabric stabilizer or placing tissue paper under the fabric to provide more traction for the feed dogs.
5. Lubrication: While you mentioned that the machine was recently serviced, it's possible that the buttonhole mechanism could benefit from some additional lubrication. Consult the user manual or contact Janome's customer support to inquire about lubrication points and recommended lubricants for your specific model.
6. Stitch length and speed: Adjusting the stitch length and sewing speed can sometimes help improve buttonhole stitching. Experiment with different stitch length settings to see if it makes a difference in stitch quality.
If you have tried all these steps and the issue persists, it may be best to consult a professional technician or reach out to Janome's customer support for further assistance. They will be able to provide specific guidance and recommendations based on your sewing machine model.
The thread cutter on my janome 7700 is stuck and clacking, then gives me an #4 error and locks up the machine can I fix it?
I have the 8200. It’s because of fluff/thread caught in the cogs that drive the thread cutter. If you slide off your accessory tray, take off your needle plate and from the rear of free arm section remove the 2 screws there (see photo) The plastic top cover will I click and lift/slide off (gently). If you look from the end under the metal plate you can see 2 plastic cogs (wish I’d taken a photo) - the smaller black one will be jammed with fluff or thread. I turned if gently with my screw driver and brushed and scrubbed with a pipe cleaner every time I turned it. Lots of fluff came out. Plugged it in and turned it on .. it worked as normal. Good luck.
I have a Janome 805, when I try to sew batting it comes up lo and wont sew
If your Janome 805 sewing machine is having trouble sewing through batting, there are a few things you can try:
- Use the right needle: Make sure you are using a needle that is appropriate for the thickness of the batting you are using. A needle that is too small or too dull may struggle to penetrate the batting layers.
- Adjust the tension: Experiment with adjusting the tension on your sewing machine. If the tension is too tight, it can cause the fabric and batting to pucker, while if it's too loose, the stitching may come out uneven. Refer to your sewing machine manual for instructions on how to adjust the tension.
- Use the right stitch length: Adjust the stitch length to a longer setting, which can help the needle to penetrate the batting more easily.
- Try using a walking foot: A walking foot can help feed the batting evenly through the machine, which may help prevent bunching and puckering.
- Use a sharp blade to trim the batting: Before sewing, make sure the edges of the batting are clean and even. Use a sharp blade to trim any frayed or uneven edges.
If none of these tips help, it's possible that there may be an issue with your sewing machine that requires a professional repair.
JANOME NEW HOME MY EXCEL 18W / MW3018 FREE ARM SEWING MACHINE -
Here are the steps to sew a buttonhole on the Janome New Home My Excel 18W/MW3018 sewing machine:
- Attach the buttonhole foot to the machine.
- Place the button in the back of the buttonhole foot and adjust the foot so that the button fits snugly.
- Select the buttonhole stitch on the machine. It may be a buttonhole symbol or a number corresponding to the buttonhole stitch.
- Set the stitch length to the desired length for the buttonhole. The machine may have preset lengths or you can adjust it manually.
- Place the fabric under the foot and lower the foot.
- Sew the first side of the buttonhole. Stop the machine when it reaches the end of the buttonhole.
- Sew the second side of the buttonhole, stopping at the end.
- Use a seam ripper or scissors to open the buttonhole carefully.
- Remove the fabric from the machine and trim any loose threads.
Make sure to practice on a scrap piece of fabric before sewing the buttonhole on your project.
I have Janome XR-23 which worked fine last time I used it. Now it wont pull the material through the foot. I have cleaned the bobbin case and oiled, The dog feed teeth go up and down freely.
If you have already cleaned and oiled the bobbin case and the feed teeth are going up and down freely, the next thing to check is the presser foot. Make sure it is properly attached and the screw holding it in place is tightened. Also, check that the pressure on the presser foot is set correctly for the thickness of the fabric you are sewing. If the pressure is too low, the fabric may not feed through properly.
If the presser foot is properly attached and the pressure is set correctly, you can also check the tension on the upper thread. Make sure it is threaded correctly through the machine and the tension is set to the appropriate level for the fabric you are sewing.
If none of these solutions work, there may be an issue with the machine's timing or the feed mechanism itself. In this case, it may be best to take the machine to a professional for servicing.
Why won't fix for 'Lo' showing in screen work?
For some reason, your machine thinks that there is something in the way, and by "lo", I'm guessing it is in the bobbin assembly. Try taking out the bobbin and the bobbin case, and see if there is anything that looks bent or scratched or isn't moving correctly. Your machine is sensing something and locking up to prevent further damage. You might want to also use some canned air to blow out any fuzz or loose threads underneath. Some of the newer computerized machines can be really particular, and the slightest bit of fuzz can throw it out of whack.
Not finding what you are looking for?
