Russell Hobbs 14449 2Speed Blender - Answered Questions & Fixed issues

Are you in the UK? If so, I got hold of replacement parts for my russell hobbs hand blender from http://www.productcareuk.com .They have a telephone number too if you cant see it on their website.Good luck!

It makes cold soups like Gazpacho and Vichyssoise, so make sure the heating / cooking function is set. If it is, ask Russel Hobbs where your local service centre is to diagnose and replace the element. https://www.google.com/search?q=Russell+Hobbs+soup+maker ..

Sometimes it is a seized shaft, does the blade turn by hand? It could be the motor has failed, or the start capacitor on the motor. It could be the electronics. There's a safety lock built into the handle of the jug. If the jug cover doesn't key into the lock properly, the motor base won't start. https://www.google.com/search?q=Russell+Hobbs+RHB315+Blender+not+working ..

Hi there... firstly is this blender a USA or UK model and do you have a Multimeter handy? if you can remove the fuse from the plug (UK only) and test t through diode mode on a multimeter or Continuity test across the fuse terminals... if it beeps the fuse is good if nothing the fuse is blown we can move on from there

if you can not find a switch to replace the bad then buy a new blender

Check continuity of the power cable. Contacts of the power switch. Carbon brush of the motor.

Overheating normally. It should reset. If it doesn't it is probably time for a new one.

Using https://www.google.com I searched the internet and found the following lInk to a possibly similar free manual: https://www.manualslib.com/manual/785919/Russell-Hobbs-Simply-Smoothie.html

There is no such button, most likely the motor has failed.

Your best bet is to open it up carefully and investigate. It's usually a minor problem unless it is old. Check it out yourself, you can't break something that's already broken and you'll gain some knowledge! :D

Check to be sure your rubber gasket is clean and in the proper place which should be between the jug and the blade asembly. Also I have seen leaking when the assembly was tightened too much. If you still have your receipt etc you may be able to exchange the unit where you purchased it. Alternatively contact the manufacturer and see if they can replace under warrenty

Knob on top push

I'm afraid I can't answer this, but am posting to say I've just discovered exactly the same problem with my newly-purchased blender - same model - and have contacted Russell Hobbs service department to find out if I'm doing anything wrong (i'm sure I'm not!). I'll post any response here.

go to culinaryparts.com you can probably order one

Contact the manufacturer. It's probably still under warranty

Direct or from eBay https://www.google.com/search?q=Kitchen+Aid+Model+KHB300+hand+held+blender+parts ..

Jimmy LavinderYou are tagging a dormant unanswered post that is 10 years old!The section up at the top is for you to ASK the Original Poster a QUESTION before giving him an ANSWER. You can't get any parts for anything online without an email address and a physical address. These parts are never found in a store. Durabrand is a cheap company of the 'sell and run' variety. There are no spares.https://www.google.com/search?q=durabrand+TSK-9368AP+partsDump it and buy a Vitamix, a company that guarantees spares forever or even a Braun, or Oster that guarantees them for 10 years...

Olabisi. It is better to create your own question rather than tagging a 13 year old question in the area where you ask the OP for further information before committing to an answer. Stir function runs the blades at a much slower speed to incorporate ingredients slowly. https://www.kitchenaid.com/pinch-of-help... STIR. To stir ingredients in a blender, start with a low, slow speed and gradually increase it to a medium speed. Blend until ingredients are completely combined. Different Blender Settings and What They Do - KitchenAid ..

Actually I do repair these stick types all of the time. The trick is getting the head off. Then its a simple Process to remove the shaft and clean inside and add bearings or bushings of needed. After removing the blade and blade holder, Remove the coupling at the top, then remove the 4 screws. After that you will see a aluminum washer. Stop here. To remove the head assembly, you need to make a large slide hammer like a split bearing. Lead or steel is good. Or a circle of cement 8 inches in Diameter and 4 inches thick. The inside hole should be as close to the diameter of the mixer shaft as possible. Cast it in two halves so when assembled it forms a ring around the shaft. Wrap this with lots of duct tape. also place a ring of duct tape around the plastic head where the cement will touch it. now wearing gloves, grab the metal base (or secure it to something with a chain or in the fork of a tree). Once secured, slide the weight quickly against the plastic head assembly. After a few hits the head should pop out. Then remove the shaft, replace the o-rungs in the center bearing, clean the unit & reassemble.Use Silicone as sealant when reassembling the body. There is no need to remove the lower seal assembly but clean it with a small bottle brush. I have included pictures of this procedure but im too ugly to make a You Tube Video. ;) These pictures are from my teaching tool and were cut to show anatomy. Theseafox Enterprises

Question edited for clarity. Question moved from Washing Machines category to Blenders. Something to do with the Outlet and Soy Milk! :>D https://www.amazon.com/gp/customer-reviews/R3S2NMMMKVYCV8?ASIN=B09L7PXN1B https://www.google.com/search?q=joyoung+a+super+power+blender+e08+error ..