Quasar VV2009 Combo - Answered Questions & Fixed issues

in side the mother board(kit)  there should be vertical IC gone.   check the vertical section  for  the IC number  and  replace it  ,     this  will solve ur problem 


thanks 

it is a setting on the remote control if all is working properly,try pressing these i know this because it happened to me. it was on my screen for 9 days before i finally got rid of it

clean the head of your vcr if that does not work then you will have to call in the tech to look into your problems goood luck.it is probably the color circuit

Try using the code 0039 and/or 0739

For combination tv/vcr the codes on the Phillips remote are 0039, 0739. I can only enter the channel I want to watch I can not use the up and down arrows for some reason.

sb2141

the one stated in the free sq4001 manual or a relic universal remote , rare i bet.

no model TV told at all.nor year made. 1967 to 2004?????? not sure what you are attempting at all first off there are no more VHF/UHF wide band TV now. its all gone. bye bye. HDTV yes , old analog is gone. buried. this TV is NOT CABLE ready, back in 1967 era,no such thing. make relic TV work needs a video to vhf channel 3/4 converter like old Pong or ATARI games had. yes there are converters. to do video to modulated channel 3/4 but not told at all what is your video choices,?sources. DVD RCA video jacks. cable modems do not have those. I bet you have cable modem or a SAT modem and converting HDTV to analog is wow hard. if not impossible one can record a video sources and convert it using PONG adapter. to old CRT motorola quasar. quasar Company ceased to exist in 2004. ! Beside Uwave ovens. and Motorola 1974 sold its television business to Matsushita Electric, now Panasonic https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2047675.m570.l1313&_nkw=+RF+Modulator+RCA+Input+Channel+3+4+Adapter+Output+&_sacat=0 the above will work ch.3/4 VHF with video sources.

Not sure why anyone would want to repair a non hd TV as the picture quality isn't usable with modern content but if you're doing it because you like restoring something vintage here are some ideas. Some CRT sets use a pulse from the back side of the flyback transformer as a starter voltage supply, it needs this short pulse to start the power supply, it's kind of like starting a gas motor, the starter only runs for a short time then the gas motor takes over, this signal needs to be measured with a scope or a high end meter, this was a common issue with a lot of older CRT sets that use this type of power supply. I'd look at the start up supply as without that the regular supply isn't operatable.

You can't., there are too many! Visual ID perhaps. https://www.google.com/search?q=Quasar+remote&rlz=1C1QJDB_enCA643CA644&sxsrf=AOaemvL0VTmVEZKq6ZL80XiQa36s1qdAkQ:1643244756606&source=lnms&tbm=isch&sa=X&ved=2ahUKEwjZ0_vf29D1AhVVj4kEHcJeBwEQ_AUoAnoECAEQBA&biw=1920&bih=937&dpr=1 ..

Your EEPROM is bad, if you can find one and have soldering skills and the equipment to remove and replace SMD devices that's the cheap way to fix( $15) if not replace the main board, in your case with the sound issue it may make more sense to replace the main as that should correct that isue as well

Your issue is .................................

type in quasar VCR model number manual

sorry you'll have to buy a new tv>^< this might cheer you up

you will need both a digital antenna and a converter box. if you can put the antenna on the roof or on a tower. if you had a newer tv all you would have to get is just the antenna

I haven't heard of a radio/tv combo since the demise of vhf tv. A reasonable radio reception could be derived from the vhf tv signal making a usable unit without the bother of an additional aerial. For use with uhf tv the radio would probably need an additional aerial for decent fm radio reception - unless the radio is am only... You don't say how old your combo is or give any details. I think the screw terminals could be intended to be connected to a 300 ohm balanced dipole aerial for radio reception only or to mount a loop aerial for indoor tv reception only, if the tv is intended for uhf analogue reception. If the tv isn't equipped with a standard socket for the usual 75 ohm coaxial type aerial lead it is possible the set manufacturer originally supplied an adaptor to fit to those two screws in order to provide a regular aerial socket. Without a much more detailed description, these are the only comments I am able to make.

Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

Without a remote control, you can't select its inputs. If you wish to buy its original remote control, contact the authorized service centre, or authorized dealer to your device brand. They can either give you a genuine remote control to your device, or can direct you, from where can you purchase a suitable one. To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. Both the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability. Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have. Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the sites. http://electro-medical.blogspot.com/ http://homenol.blogspot.com/ http://electrohelponline.blogspot.com/ http://remotesearch.blogspot.com/ Universal remote controls are available at most of the electronic spare part selling shops. Visit some on-line sites too, which deals with electronic spare parts.

Do a factory reset to this set and then check. There are two methods of resets. Factory reset and hard reset. To make it a hard reset unplug the set from the AC mains wall socket and reinsert after an hour or so. To do a factory reset, you have to enter it's service mode option. If you wish to get more details visit the site linked here. http://electronicshelponline.blogspot.com/

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. The site has set-up code list & set-up procedure to many popular brand remote controls. The site has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Set-up code list to many brand remote controls also is given. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily. http://homenol.blogspot.com/ http://remotesearch.blogspot.com/ http://electronicshelponline.blogspot.com/ http://electrohelponline.blogspot.com/ Programming Notes • If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote. • Sometimes the first code that "works" with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality. This is a trial and error procedure; and quiet time consuming. You might have to check different codes said for your device. Search the site by type in the "brand name" to your device; to which you want set-up codes; in the "Search box at the top right of the display window" to get gathered related posts.