20 Most Recent Curtis LCD2424A 24 in. LCD HDTV - Page 8 Questions & Answers

www.schematicscom.blogspot.com/

If you can; contact me.

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement.

You have to adjust the laser head, by turning the trimer which is over the laser pcb... if you turn thiw a little, you have to try if its ok. ifits ont try to adjust again until you find the right position of the trimmer...

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily. http://remotesearch.blogspot.com/ http://electronicshelponline.blogspot.com/ http://electrohelponline.blogspot.com/ Search the site by type in the brand name of your device, in the "Search box at the top right of the Home page display" to see the set-up codes to your device, with different brand remote controls.

Download the "parts" manual: http://www.curtisint.com/web/browser.asp?productID=LED1930A&catName=LED%20TELEVISIONS to find the part-number.

Comcast Remote Codes Program Your Comcast Remote Control

I assume other remote functions work since you only mention turning off/on. this would most likely be a bad switch in the remote and probably not be worth repair. You can find a replacement here:

http://customer.xfinity.com/help-and-support/cable-tv/finding-your-remote-control-programming-code

Without a model number, I can't give you a direct link.. go here and enter your info and get operators manual: Manuals CURTIS INTERNATIONAL

http://www.curtisint.com/html/custservice/manuals/CUR_RT701A_EN.PDF I could only find users manual.. simple, but obvious troubleshooting

If the TV work properly, the disc loading mechanism has the fault. A broken belt, or a broken gear wheel. You have to take out the CD mechanism out from the set to repair. Contact any service technician. In very rare cases, there will be very small pin hole at the front of the mechanism [usually just below the DVD tray or at its side, by which you can insert a straightened paper clip into and press a little, and pull out the disc tray, to take the Disc out in emergency, even if the set has no power. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Try a hard reset to this set, and check. If it do not help you, the main board to it is faulty. There are two types of reset to TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight; will be better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

totals a good one

More likely the battery is dead. Try to replace it with the working one and check.

This is common, if remote has been dropped or liquid spilled. Best to buy cheap universal remote.

2908,2995. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily. http://remotesearch.blogspot.com/ http://electronicshelponline.blogspot.com/ http://electrohelponline.blogspot.com/ Type in the brand name of your device, in the search box [at the top right] of the display window and the Search will start at once as you type in, and will show you all the related posts. It will make surf easy. Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls.