20 Most Recent Kyocera Mita FS-3820N Laser Printer Questions & Answers

0helpful
1answer

Kyocera call service 4200:040797

Means that the laser unit is off. You should check the cables for the laser unit
7/27/2014 2:09:58 PM • Kyocera Mita... • Answered on Jul 27, 2014
0answers
0answers
0answers
0helpful
1answer

Paper stuck in back of printer - unable to remove

youll have to take off the back off and try to get at it from there you should be able to see the bits of paper somewhere just take bits off till you get to it , not an easy job on any printer
10/5/2012 2:31:45 PM • Kyocera Mita... • Answered on Oct 05, 2012
0answers
0helpful
1answer

My Printer Kyocera FS-3820N keeps

Hi,
In order to get the printouts on the top bin, all you have to do is close the rear tray.

Hope it helps! Good Luck! Thanks for using Fixya!
CreativeTECH
9/20/2011 10:41:07 AM • Kyocera Mita... • Answered on Sep 20, 2011
0helpful
1answer

Kyocera 3820n doesn't work right on my macbook OS X 10.5

if you have a mac os x operating system... you already have drivers built into your mac printer menu... try installing the generic print driver and see if that helps... sometimes it works better than the manufacturer's driver... I’m happy to assist further over the phone at https://www.6ya.com/expert/norman_d2fa496dce30c65d
8/31/2011 5:56:12 PM • Kyocera Mita... • Answered on Aug 31, 2011
0helpful
13answers

Hi, lost password and want to

you might out of luck because they company wont give out the procedure or they might charge you $50.00 for procedure. Below is the what I found on the web for different model but the procedure is the same (the printer server card is different either 1x or 2x, but you only have one for each printer)

Turn off, unplug.

2) Remove the IB-2X card. Mine is secured with two thumb screws. Just give it a tug and it comes out.

3) Locate the jumper. Remove it, rotate 90%, and install on SW2.

4) Reinstall IB-2X.

5) Plug in and power up, wait for READY.

6) Turn off, unplug.

7) Remove the IB-2X card.

8) Remove jumper, rotate 90%, and reinstall in previous position.

9) Reinstall IB-2X.

10) Unplug the network cable.

11) Plug in and power up, wait for READY.

12) Admin password is now blank. TCP/IP settings: DHCP is on, subnet mask is 000.000.000.000, default gateway is 000.000.000.000, IP address is 000.000.000.000. Change settings to desired.

13) Reconnect network cable.
They also have something call ResetLan tool, but it costs you.
Try above step at your own risk. Thank you


7/22/2011 10:32:05 PM • Kyocera Mita... • Answered on Jul 22, 2011
0helpful
1answer

Not printing a whole page

Have you tried taking the toner out and shaking it? It could be that it is running out of toner. It also could be something to do with the rollers inside.
3/5/2011 2:58:45 AM • Kyocera Mita... • Answered on Mar 05, 2011
0helpful
1answer

When I go to print

The waste toner box is located on the right hand side of the printer. There is a door/cover that opens up on the right side. It is a milky white plastic container. Check to make sure it is there and installed properly and the door is fully closed. If all that is correct it my be full.

There should be a new waste toner container in the toner box (along with a toner). The toner and waste toner are normally replaced at the same time.

If you don't have a new waste toner container you can tray emptying the one that is in the printer BUT be very careful. The toner is a fine powder and can get all over if spilled. If you ever spill toner never use water or any other liquid to try and clean it, that will just turn it to a liquid ink.Brush it off your cloths and vacuum it up.

If you do try and empty the container and the machine continues to tell you it needs to be replaced it can be because there is still toner on the inside of the toner container and the sensor is seeing it there.

I hope this is helpful,
Shawn
1/29/2011 12:33:33 AM • Kyocera Mita... • Answered on Jan 29, 2011
0helpful
1answer

Error code 7001:0014607

Kyocera Mita FS-3820N



Hello, This error code (7001) refers to a Toner motor error.


• Toner motor is overloaded. TNMOC is detected by sampling every other

100 ms in 2 seconds since the main and toner motors are activated following

the Replace toner Clean printer, message after the "Toner low" is detected.


Recommended action is to change the toner pack.


If this does not resolve the issue then the developer should be changed.


If neither of those resolve the issue, then likely the internal circuit board called the engine controller may be bad.


If this is the case the printer will need to go to an Kyocera Repair Depot.


I hope this has been of assistance.
http://www.fixya.com/uploads/images/prefab_21.jpg

1/18/2011 7:01:47 AM • Kyocera Mita... • Answered on Jan 18, 2011
Not finding what you are looking for?
Kyocera Mita FS-3820N Laser Printer Logo

35 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Mita Office Equipment & Supplies Experts

Marvin
Marvin

Level 3 Expert

85241 Answers

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

7025 Answers

Clive
Clive

Level 3 Expert

4362 Answers

Are you a Kyocera Mita Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kyocera Mita Office Equipment & Supplies

  • Kyocera Mita Office Equipment & Supplies

Most Popular Question

paper stuck in back printer unable

  • Office Equipment & Supplies
Loading...