20 Most Recent D-Link DAP1360 IEEE 80211n (draft) Wireless Access Point DAP1360 (DAP1360E) Pre80211n Questions & Answers

http://support.dlink.com/emulators/wbr2310/lan.htm

talk to Dlink directly. (no main router stated, model?) it is just a RANGE extender, 7 different modes Access Point, Wireless Client, Bridge, Bridge with AP, Repeater, WISP Client Router or WISP Repeater Compatible with 802.11b and 802.11g Devices(no main told) . repeater mode (1 of 7) is covered in the manual and wirlessly bridges to the main AP, and extends the range of the wifi to the new zone,(goal?) ( do this here but use Ethernet from main to new AP) vastly better. page 26 in your manual covers setup for Repeater mode. did you do that? step one is the SSID, use a new name here, not same as other AP or other wireless nodes, ok? step 2, select repeater I never use WPS so I skip this (its insecure) pick manual page 29 find our main router, SSID name, or survey it. this is very important to marry the new AP to the old router SSID. my main would be WPA2, id not use any others (security) then type in the mains , Password, 8 to 32 chars. its done. update the firmware in both routers first? be wise that. I never do this ,all it does is slow down wifi in 2nd zone. for sure walls present ! in the line of site paths. I bridge them with ethernet (wired) now both zone go full speed.

Try turning off the WEP and connecting. Are you using repeater mode on your router, or just adding the repeater to your network?

It should be 192.168.0.50. See link: Dlink DAP 1360 Login Instructions

How many other wireless networks are detected at your location? It could be interference from those other routers.

Go to this link http://support.dlink.com/ProductInfo.aspx?m=DAP-1360 and download the user manual for your DAP-1360. Configure it in the WISP mode following the manuals instructions.

You don't need to connect via ethernet. In your laptop set the IP address to 192.168.0.2. subnet 255.255.255.0 This will probably temporarily disconnect you from your internet but you can reset the IP address back later. It might be a good idea to write your current settings down for later. Open your browser and enter dlinkap or 192.168.0.50 You will connect to the Dlink AP follow the directions in the user guide found at the link below. http://global.dlink.com.sg/site_support/DAP-1360/Manual/DAP-1360_Manual_v1.00.pdf

i want to setup issyleb dap1360

reset router and use default password to reconfigure.

1) reset your browser (internet explorer).2) connect your access point (AP) to your pc directly using LAN port and CAT5 cable3) type in default IP address of AP->192.168.0.50 (Or Current IP address of Ap) in browsers address bar.4) username = Admin and blank password (i.e. password is no text)5) Click on Advance Button then click on Wi-Fi Protected Setup button on left menu pan.6) See the image below record your current pin, if you wish to change it just press generate new pin button.7) Don't forget to say thanks :)

Reset using the button on the back the do an ipconfig - so if you ip is 192.168.1.1 try that to get in to the router

hi I want an explanation of the problemyou can do a rest to this modem!!!!

YES.ALL YOU NEED IS TO LOG IN THE ROUTER UI AND SET IT,

If the default password on the D-Link has been changed then-
To reset the D-Link back to the default settings -
Press and hold the RESET button at the back of the router with the power ON untilthe LEDs flash at the time the release the RESET button.
Connect a LAN cable from the D-Link to your laptop/computer's LAN port, openthe browser on your laptop/computer and enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter) You can now change the default password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.
To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Most likely your access point is losing connection with your router. I looked into buying one of these, but decided against it when I saw on some message boards its problem with connectivity. Best thing to do is do a hard reset and then update your firmware to the latest version.