here's the manual..
i did not read thru the whole thing but there are quite a few removal items that i'm sure will lead you to drawer removal.
Hope this helps you.
https://www.scribd.com/doc/6462163/DD601V2-Manual
This could be the control board that has failed, the door latch switch is bad, the solenoid in the valve is open. So if you post the model we might be able to get more info for you .
not sure how handy you are? but here goes..
Had the same problem with a samsung two drawer.
Dishwashers are basically all the same just different buzzers and bells.
Start with the top unit. As it may be leaking and going down too the lower one. UNPLUG or disconnect power first!!
To find leak...open the drawer on the drawer rails there should be a drawer release tab there both sides. release and pull out the drawer a few inches. (drawer empty!)
on the bottom there will be a pan attached by some screws.
remove screws drop the pan. Now look where it's wet or shows signs of leaking.Could be just a hose and a clamp,
or a cracked pump. Just a hose or clamp replace. probably though a gasket on the drain assembly.
I am assuming your'e not in the states.
and my access to those parts to help are limited.
If you are handy at all it'll only take up some time and patience to disassemble and fix. Keep screws organized
by size and location as it can get really bad if not!
Hope this helps a little.
Let me know if you have any other questions.
Have a good day/night.
it will most probably have corroded bearings in the motor, theres not much you can do other than replace the motor, ive never seen individual parts for sale for motors
The code E6 is for the flood switch
Pull the appliance out, tip it back about 45 degrees and see if water runs out of the base.
If it does, drain the base (under where the tub) completely and the anti flood should reset.
If there is an aquastop device on your fill hose, after draining the base, turn off the water supply, disconnect the aquastop device and allow it to de-pressurize. Connect it back up and try again.
If it happens again, you'll need to check for a leak.
The normal cause is over foaming, using multifunction tablets and rinse aid, or just spilling rinse aid.
there is water in the base setting off the flood sensor, you will need to remove the bottom draw and dry the water up with a towel (make sure the power is off and unplug it from the power point) then you will need to do a bit of testing to locate the cause of the leak, if your lucky the leak was caused by incorrect dish stacking or something too big in the draw
I have had issues with the top dish drawer for a while, it will start for several minutes and then beep a few times, open its lid and stop. it did this after a few min OR it will run for a while and shutdown after 90 min or so. I tried swapping parts with the known good dish drawer and the problem stayed with the top dish drawer. it turned out to be a mechanical issue. this is a link to a video I created that will explain this better.
https://youtu.be/Ttco5KfVyWs
I read a few tips on this site about the above problem.
Then rang Fischer and Paykel. My dishwasher is a two drawer.
They suggested using chux rolled up and pushing down aid dispenser.
After pulling out, throw out and keep doing this with a fresh rolled up piece of chux.
I did it about three times. Then I slowy poured some water in. Used fresh chux rolled up. Repeated the process a couple of times. Then repeated with dry chux, till it was all dry as much as possible. Then I poured half a cup of white vinegar onto the bottom of dishwasher and did a rinse cycle, checking for foam, every now and again.
The white vinegar stops the foam.
All seemed good.
Then I did an empty full wash "test". All good at the end. No froth at all during cycle.
After the "test" wash, I filled the aid dispenser with "rinse aid" not dishwashing liquid.
All up it took me about 20 minutes.
Thought I would pass on. And don't panic, (like I did). The woman at Fischer and Paykel was so helpful and said it is a common thing, so I didn't feel so bad.
this model doesn't have one it just has an air vent located about halfway up on the right side of the machine, why would you like to know where the fan is? what is the problem your having?
