20 Most Recent D-Link DAP-1522 Xtreme N Duo Wireless Bridge/Access Point (DAP-1522/B) Pre-802.11n - Page 7 Questions & Answers


Depending on the model, D-link used 192.168.0.1 for many of its routers but on some a different one - or if previously owned this may have been changed.
The final solution is a factory reset of your router. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset

If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can ssets-up form scratch.

D-Link Computers... | Answered on Jan 06, 2017


Login in using your browser and go to the wireless settings and set-up a wireless password/key. Remember the key because each device will now need it to connect. You can also turn OFF Broadcast SSID and your network name will not be shown on anyone's device. You must remember the network name when using this method.

D-Link Computers... | Answered on Jan 06, 2017


Usually that indicates a fatal issue. But try The final solution is a factory reset of your router. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset

If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can ssets-up form scratch.

D-Link Computers... | Answered on Jan 06, 2017


The network password or the login password?
Login into you router using your browser (connected by a LAN cable) and under the wireless section you should see the network password.

The final solution is a factory reset of your router. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset

If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can ssets-up form scratch.

D-Link Computers... | Answered on Jan 06, 2017


Try a facotry reset. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset

If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can ssets-up form scratch.

D-Link Computers... | Answered on Jan 06, 2017


Usually you can login on your browser to you router and go to the management section to check for firmware updates and select that button and it will download and install the firmware. On some models, you have to go to the D-link web site and look for firmware updates for your router. Always check what you current firmware you have installed and check the version of you router modem (A, B, C etc). Then you can manually download the firmware (usually in a ZIP file), open the zip file, and then using your browser connected to the router look for Update Firmware. You will have to go to where (folder) you saved the downloaded update and select that file. It is recommended that you update using a LAN connection and not a wireless connection.

D-Link Computers... | Answered on Jan 06, 2017


Try a factory reset. login to your router and under setting go to factory reset. Once done you will have to set-up you device from scratch.

D-Link Computers... | Answered on Jan 06, 2017


Did you do a factory reset? That will restore it to it original out of box settings and often solves many issues. If that does not solve the issue, you may have a dead router.

D-Link Computers... | Answered on Jan 06, 2017


You can perform a factory reset by logging into the router and under admin settings select factory reset. You can also do it by locating a small hole on the back side of the router, and using a tip of a paperclip insert it into the hole for about 10 seconds with the power on.

Usually you can login on your browser to you router and go to the management section to check for firmware updates and select that button and it will download and install the firmware. On some models, you have to go to the D-link web site and look for firmware updates for your router. Always check what you current firmware you have installed and check the version of you router modem (A, B, C etc). Then you can manually download the firmware (usually in a ZIP file), open the zip file, and then using your browser connected to the router look for Update Firmware. You will have to go to where (folder) you saved the downloaded update and select that file. It is recommended that you update using a LAN connection and not a wireless connection.

D-Link Computers... | Answered on Jan 06, 2017


The blinking triangle light indicated the wireless portion of your router is active and sending/receiving connections.

D-Link Computers... | Answered on Jan 06, 2017


You will have to do a manual factory reset. with the power on, find a small hole usually on the back side of the router. Using a pencil of tip of a paper clip, push it into the hole for about 10 seconds. This should reset to router to factory settings and erase any password information.

D-Link Computers... | Answered on Jan 06, 2017


Usually you can login on your browser to you router and go to the management section to check for firmware updates and select that button and it will download and install the firmware. On some models, you have to go to the D-link web site and look for firmware updates for your router. Always check what you current firmware you have installed and check the version of you router modem (A, B, C etc). Then you can manually download the firmware (usually in a ZIP file), open the zip file, and then using your browser connected to the router look for Update Firmware. You will have to go to where (folder) you saved the downloaded update and select that file. It is recommended that you update using a LAN connection and not a wireless connection.

D-Link Computers... | Answered on Jan 06, 2017


Go to the D-Link website under the support section and look for your model of router. There should be a downloadable manual in PDF format.

D-Link Computers... | Answered on Jan 06, 2017


Usually you can login on your browser to you router and go to the management section to check for firmware updates and select that button and it will download and install the firmware. On some models, you have to go to the D-link web site and look for firmware updates for your router. Always check what you current firmware you have installed and check the version of you router modem (A, B, C etc). Then you can manually download the firmware (usually in a ZIP file), open the zip file, and then using your browser connected to the router look for Update Firmware. You will have to go to where (folder) you saved the downloaded update and select that file. It is recommended that you update using a LAN connection and not a wireless connection.

D-Link Computers... | Answered on Jan 06, 2017


Check to make certain you have the correct update. D-Link has model variations like "A" "B" "C" and each has a different update requirement. So if you tried to update your "A" model with "B" firmware, that might produce an error. Contact D-Link email or chat tech support for details.

D-Link Computers... | Answered on Jan 06, 2017


The speed of your internet is determined by your service provider and their modem. If possible, connect directly to the modem to check the speed. If you suspect you D-Link router is not allowing you to get full internet speed, first a Hard Reboot of you Router and Modem.
If that did not solve the issue, try a known working LAN 5e cable between your modem and router. After you have established it is not a cable issue, do a factory reset.
I had an issue where my speed to the internet modem was fine, but the router LAN connections only provide a faction of the internet speed. After testing cables, etc I did a factory reset and it restored full connection speed on my router LAN ports.

D-Link Computers... | Answered on Jan 06, 2017


Modems do not use IMEI -- it's only mobile-phones that do.

D-Link Computers... | Answered on Sep 18, 2016


Go to settings then wifi connect your wifi network


skype id : [email protected]

D-Link Computers... | Answered on Sep 13, 2016


run the command getmac on cmd and you will get the mac address of mac address of computer


skype id :[email protected]

D-Link Computers... | Answered on Sep 13, 2016

Not finding what you are looking for?
D-Link DAP-1522 Xtreme N Duo Wireless Bridge/Access Point (DAP-1522/B) Pre-802.11n Logo

Popular Tags

34 questions posted

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Mike

Level 3 Expert

4369 Answers

k24674

Level 3 Expert

8091 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

D-Link Computers & Internet

  • D-Link Computers & Internet

Most Popular Question

cannot access either dlinkap or

  • Computers & Internet
Loading...