20 Most Recent
VinoTemp (VT60GNV) Wine Cooler - Page 2 Questions & Answers
Vinotemp wine cooler won't cool
It sounds like your control module is bad. Vinotemp does list the replacement part as available at a cost of around $35
12/21/2010 12:39:05 AM •
VinoTemp...
•
Answered
on Dec 21, 2010
We have a 32 bottle
In that case the refrigeration from the left side is not operational on your cooler. In this model the thermoelectric system is used - the cooling is done thru the Peltier effect, not with a compressor. Because of that when the cooling element fails it must be replaced in its entirety, it can't be repaired.
This is a big job that involver the dismantling of the entire unit. Make arrangements to relocate the reds and call Vinotemp at 1.800.777.8466 - they will guide you to the nearest authorised repair shop.
11/9/2010 6:45:35 AM •
VinoTemp...
•
Answered
on Nov 09, 2010
The motor is running but
Hi,
Many times a freezer and/or refrigeratordo not work right because of a dirty condenser coil...there are also many otherthings that can go wrong.
If you are hearing a clicking or buzzing then check out thelast two tips.
If your refrigerator is running but warm, then...
Check out this tip that I wrote about that... it is a great place to starttrouble shooting your unit...and something that you can do rather then callinga repair person to do a simple thing for you...
Refrigerator
Condenser Coil Cleaning Refrigerator Repair
Refrigerator Troubleshooting Refrigerator Compressor
Refrigerator Compressor Start Capacitor and Start Relay
heatman101
9/16/2010 2:09:46 AM •
VinoTemp...
•
Answered
on Sep 16, 2010
Vinotemp 2 zone wine cooler flashes
Not sure, but did you clean the filter in the back? Ours has that, and the temp starts creeping up every few weeks until I clean it. But we've never been able to get it below 58 or so, and in the last year, not below 60. I think that's just the nature of this type of cooling. Our house is also at 80. But, can keep it at 60 with the above cleaning.
9/17/2009 10:15:23 AM •
VinoTemp...
•
Answered
on Sep 17, 2009
Cooler keeps on triggers breaker
If it is tripping the breaker, stop plugging it in. The breaker is tripping because something is wrong, and continually resetting the circuit WILL cause a fire. Either return the unit, or have an electrician look at it. You can also try plugging it into another circuit in your house to isolate the problem, but please don't repeatedly reset the breaker, there IS a problem somewhere.
5/27/2009 6:11:39 PM •
VinoTemp...
•
Answered
on May 27, 2009
Vinotemp VT-60 Condenser won't shut off, unit running way too cold
It might be a sensor or control board problem. Any appliance repair place should be able to help you out with this. Or you can try contacting the
manufacturer directly for help or if you need to purchase replacement parts. Otherwise, my cheapest suggestion would be to hook the cooler up to a timer, so you can turn the unit on and off maybe every 20 minutes or so. That should help keep it from causing more harm and then you can monitor the temperature with a thermometer. Hope that helps!
9/4/2008 5:02:05 PM •
VinoTemp...
•
Answered
on Sep 04, 2008
Cannot close vinotemp
The bottles are too long, and its probably hitting the glass. Try installing without it being double deep and see if that works.
8/11/2008 11:36:05 PM •
VinoTemp...
•
Answered
on Aug 11, 2008
Wine-cicles
I found the vinotemp trouble shooting webpage that has good info for several different VT models. Here is the link.
http://www.vinotemp.com/troubleshoot_pdf.htm
I emailed VT and they gave me a price for the parts
VT-TC32ECB -$34.95 (control board)
VT-60Sensor -$14.95
here is their services information
Jane Barron
Service Department
VINOTEMP INTERNATIONAL
[email protected]
T 310.886.3332 x231
800.777.8466
F 310.886.3310
6/13/2008 12:49:16 AM •
VinoTemp...
•
Answered
on Jun 13, 2008
I have a simmons nuflex bed that is fine except the foot wont raise. Massage works on foot, but it just wont lift. No clicking or noises when using the remote
If the foot of your Simmons Nuflex bed will not raise, there may be an issue with the motor or the lift mechanism. Here are a few things you can try to fix the problem:
- Check the remote control: Make sure the remote is properly functioning and the batteries are not dead. Also, check that the foot lift button is not stuck.
- Check the wiring: Check the wiring between the remote, the lift mechanism, and the motor for any frayed or disconnected wires. If you find any damaged wires, they will need to be repaired or replaced.
- Check the lift mechanism: Inspect the lift mechanism and look for any visible damage or debris that may be preventing the foot from raising. Clean the lift mechanism and lubricate it with light oil.
- Check the motor: If the motor is not functioning properly, it may be preventing the foot from raising. If the motor is faulty, it will need to be replaced.
If you are not comfortable with these steps, or if the issue persists after trying them, it may be best to contact Simmons customer support or a professional technician for further assistance. They may ask you to provide your bed's serial number and other information to help troubleshoot the problem.
4/17/2024 2:20:33 AM •
Furniture
•
Answered
on Apr 17, 2024
Not finding what you are looking for?