20 Most Recent Kenmore 24 in. 15689 Built-in Dishwasher - Page 6 Questions & Answers

0helpful
1answer

Model 15754 Kenmore built in dishwasher leaking

take off the bottom panel ....... check for the leak .... could be the fill valve connection ..... motor pump assembly (most liklely) or a drain hose/pump issue....if the DW is noisy as well go shopping ...
7/22/2009 7:31:53 PM • Kenmore 24 in.... • Answered on Jul 22, 2009
0helpful
2answers

Our Kenmore dishwasher 665.1726

Once the 4 screws are removed everything should come off. be careful as the outside rubber bit on the surrounding does not come off with these screws, so avoid pulling that.The bottom wash arm should be unclipped out first.Then remove the screws and take pictures with a camera for referencing to help put back.From here it's self explanatory and you should be able to clean everything and put back together.
7/12/2009 4:35:16 AM • Kenmore 24 in.... • Answered on Jul 12, 2009
0helpful
1answer

Lock light stuck on, dishwasher will not work

We had turned the power off at the breaker but only flicked it on and off, a friend recommended we turn off the power and leave it off for 5 minutes then turn it back on. This solved the entire problem!
7/12/2009 2:54:58 AM • Kenmore 24 in.... • Answered on Jul 12, 2009
0helpful
1answer

Water is not comeing on when you put it on wash

It sounds like you (or the installation technician) forgot to turn the water on at the angle stop (where the supply line connects into the water supply). If you have a two-outlet angle stop, check the sink faucet to make sure you have water. If you have water, check the electrical connections and the breaker to make sure you have power. These are the main points to check for this kind of issue.
7/3/2009 3:50:11 PM • Kenmore 24 in.... • Answered on Jul 03, 2009
0helpful
1answer

Kenmore Ultra Wash dishwasher

check and see if you are getting ac 110 volts to your water vave when trying to start the unit. if no power check your breakers and /or the incoming power to your dishwasher if they are ok and show 110 voltage coming to the unit then you probably have a control board or touchpad problem which would need a little more detailed check out.
If you do have ac 110 to your water valve then you may just have a bad water valve. Because the washer has to fill first. Hope that helps!!
7/2/2009 11:16:26 PM • Kenmore 24 in.... • Answered on Jul 02, 2009
0helpful
1answer

Dishwasher makes a loud noise until I turn on the water in sink

You have too much water pressure it sounds like for the fill valve to operate properly. I am assuming it is chattering? How much water pressure do you have? If its too high an inexpensive regulator can be purchased at most plumbing supply stores to install in the DW supply line.
7/1/2009 2:25:15 AM • Kenmore 24 in.... • Answered on Jul 01, 2009
0helpful
1answer

Kenmore dishwasher no power

Check the following areas for faults.

1. No power to the dishwasher
Make sure there's power getting to the dishwasher. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power. Sometimes the power cord disconnects at the dishwasher (inside the junction box, behind the bottom kick panel), if this is the case, the wiring must be repaired or replaced.

2. Door switch
Replace if defective.

3. Timer or control board
Replace if defective (note: uncommon problem).

4. Selector switch
Replace if defective (note: uncommon problem).
6/22/2009 9:32:33 PM • Kenmore 24 in.... • Answered on Jun 22, 2009
0helpful
1answer

Clean light flashes and dishwasher wont start

HI, this is a dirty filter alert. it could also be a control fault as well. clean the filter and, disposal as well. if this alert cannot be cleared, replace the control board or, timer.
6/22/2009 9:30:25 PM • Kenmore 24 in.... • Answered on Jun 22, 2009
0helpful
1answer

Clean light blinks, dishwasher won't start,

turn the power off at the breaker for 10 minutes and check it then.
6/11/2009 11:56:48 PM • Kenmore 24 in.... • Answered on Jun 11, 2009
0helpful
1answer

Kenmore dishwasher is not washing properly and leaving dirty wate

yes you can, what you want to do is right after you read my solution... rate it. :D but anyways wht you have to do is take out the filter underneath the bottom tray where the dishes go. and clean out all that yummy wet gross food from last week. it'll be all gunked up. that's stopping the dirty water from draining.
6/2/2009 12:50:37 AM • Kenmore 24 in.... • Answered on Jun 02, 2009
0helpful
1answer

Dishwaser does not fill

Hi. You can test the fill valve for voltage. If it is getting 120V and n water is coming in, change the valve.
Some models you can pull the float out.
When you lift it up and down, can you hear it clicking?
Please let me know if I can assist you further.

Vic
5/30/2009 3:19:44 AM • Kenmore 24 in.... • Answered on May 30, 2009
0helpful
2answers

Kenmore UltraWash QuietGuard 4 making horrible

you have a peace of glass or plastic stuck in bottom
around the sprayer arm
5/30/2009 1:08:36 AM • Kenmore 24 in.... • Answered on May 30, 2009
0helpful
2answers

Lock on light flashing

I finally decided to calm down and use my head and managed to solve the problem. I read the instructions that are on the top of the dishwasher door. ( Smart move on my part HUH!) It said that when the door lock light is on everything is disabled. Hold the air/dry button down for 4 seconds and the lock light will go out. Guess what, IT WORKED. Here is what I learned from this. Always read all instructions. I spent $9.95 for an answer that was right in front of me. Humans can be so dumb I am!!!!
5/28/2009 10:30:24 PM • Kenmore 24 in.... • Answered on May 28, 2009
0helpful
1answer

How do i remove lower spray arm on a kenmore13854

i hoe this help you to answer your question. copy n paste
http://www.youtube.com/watch?v=PbkY_SDA8jo&NR=1

Was this helpful?
5/13/2009 1:46:55 PM • Kenmore 24 in.... • Answered on May 13, 2009
0helpful
1answer

My kenmore elite ultrawash dishwasher,

youll need to enter a diagnistic mode, press in this order, hi-temp(sani-rinse)----heated dry--hitemp---heated dry... all lights should light, close door and let cycle for about a min, htne press the cancelbutton, you should be good to go, the buttons on your model may read slighty different names, if this "toggle of buttons" does not work, you can remove thelower access panel and htere willl be a tech sheet/trouble shoooter behind the panel, in there it will explain how to enter diag/test mode
4/29/2009 3:01:20 PM • Kenmore 24 in.... • Answered on Apr 29, 2009
0helpful
1answer

Side mount brackets for kenmore dishwasher

Where can I can sears part # 170664 side mount bracket for a kenmore dishwasher mohel 13593?
4/15/2009 3:38:07 PM • Kenmore 24 in.... • Answered on Apr 15, 2009
0helpful
1answer

Dishwasher runs, water doesn't drain out

sounds to me that you may have some suds residue in the dishwasher that keeps it from draining completely. Get you some dishwasher cleaner which you can purchase at wal-mart or wherever you buy your detergent, and clean out your dishwasher. It is a inexpensive test. Alot less expensive than having a tech come to your house. Make sure that your drain hose is mounted higher that where it goes into the drain. This is also a common problem that I encounter in the field. Hope this helps. Let me know if I can help you futher.
4/5/2009 11:58:53 PM • Kenmore 24 in.... • Answered on Apr 05, 2009
0helpful
1answer

Dishwasher not filling all the way

hi,
There's no water entering the machine
If there's no water entering your dishwasher, check these:

Water-inlet valve
Float switch

Water-inlet valve
The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely replace it. It's usually located behind the lower access panel on the left or right side. It's the device with the main water line (usually copper) from the house, a rubber tube to the dishwasher, and two wires attached to it.


Float switch
The float switch is a small electrical switch that's located right below the dishwasher "floor." Above the switch, on the inside of the dishwasher, is a plastic cylinder that floats up as water fills the dishwasher. If this switch is defective, or if the plastic float gets caught or trapped in the raised position, the water can't enter the dishwasher. If the float switch is defective, you need to replace it.

good luck.........
3/28/2009 7:56:22 PM • Kenmore 24 in.... • Answered on Mar 28, 2009
0helpful
2answers

Liquid dish soap in the dishwasher

You will get some sudsing, but just soak up what you can with a towel and then run 1 or 2 cycles and you should be OK.
3/24/2009 1:24:47 PM • Kenmore 24 in.... • Answered on Mar 24, 2009
Not finding what you are looking for?
Kenmore 24 in. 15689 Built-in Dishwasher Logo

Popular Tags

217 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Cindy Wells

Level 3 Expert

6395 Answers

Paul Carew

Level 3 Expert

3699 Answers

Vernon Taylor

Level 3 Expert

7446 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenmore Dishwashers

  • Kenmore Dishwashers

Most Popular Question

kenmore ultra wash quiet guard 3

  • Dishwashers
Loading...