20 Most Recent Kenmore 43052 Front Load Washer - Page 8 Questions & Answers


Probably a worn-out bearing; try rocking the empty drum by hand within the tub. If it is loose on the hub, discontinue use to avoid further serious damage, and get a service engineer to take a look.

Kenmore Washing... | Answered on Oct 08, 2019


Could be two issues. Could be the pump has sprung a leak or a hose has split. Not sure about the starting problem but would check where the leak is first so you do not spend a lot of money on the starting problem the find you have a lot of money spent in the water problem.

Kenmore Washing... | Answered on Oct 07, 2019


F20 means either Hot or Cold water is taking too long to fill. remove hoses and fill into a buck to verify you have good household pressure. if not, call plumber to resolve. If hoses are putting out good pressure, inspect water valve screens, one or both may be partially clogged with sediment or sand. If they are clean, I recommend replacing the water valve.

Kenmore Washing... | Answered on Oct 05, 2019


Sounds like your water entry problem is most likely a water entry solenoid.
As for draining out water try this...
Get a couple of gallons of water and manually place it in the bottom of the dishwasher. Hit start and see if this drains the water. If it does not, see if this water at least is able to be pumped around inside by waiting for the wash cycle to begin. That tells you that the wash pump is OK. Next hit the cancel button and see if it drains on that command. If the water placed in the dishwasher still remains there without draining that is probably a timer control board if this is part of the water entry problem as well.
Having two separate issues .....
water in and water out not functioning suggests a control board issue. Hope it's not the board. They are expensive.

Kenmore Washing... | Answered on Oct 03, 2019


your hot water goes through the water heater so contaminates settle in the heater. the cold does not, there is a screen inside the fill valve where the hose hooks to the valve on the machine. if this in not plugged then the fill valve will have to be replaced. because of the build up of contaminates..

Kenmore Washing... | Answered on Oct 03, 2019


Sounds like either a wire has come loose from the switch or the motor that spins the the ( may be integral part of switch ) has gone bad.

Kenmore Washing... | Answered on Oct 03, 2019


Because quilts, towels, etc. hold a lot of water, they will only release that water during the spin cycle. If the spin rate is too high, the machine will sling water over the top of the tub thence down and onto the floor. To prevent this, reduce the spin rate from high to low. If you find they are still too wet, run a second spin, only, cycle on a higher setting.

Kenmore Washing... | Answered on Oct 02, 2019


Unplug it for 1 hour and plug back in. Hope it works.

Kenmore Washing... | Answered on Sep 30, 2019


F5laundry chuy?n cung c?p M?y v?n ph?ng - ?i?n m?y - Thi?t b? s? - M?y gi?t c?ng nghi?p gi? c?nh tranh h?ng ch?nh h?ng uy t?n v? h?ng ??u
https://f5laundry.net/

Kenmore Washing... | Answered on Sep 25, 2019


I have never yet tackled a top loader but I wouldn't be afraid to - clearly you need to follow the cable to a point where the voltage can be checked along the circuit - presumably part of the cabinet can be removed.
Sometimes where there is no clear instructions it is a matter of removing screws until something falls off and then later remembering what you did.

Kenmore Washing... | Answered on Sep 21, 2019


How long have you had it? Generally, washers won't operate with the lid up for safty reasons. If the lid is down and it doesn't operate, the lid safety interlock may be bad or loose. If visible, try pushing the interlock down with a screwdriver.

Kenmore Washing... | Answered on Sep 09, 2019

Not finding what you are looking for?
Kenmore 43052 Front Load Washer Logo

Popular Tags

36 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Vernon Taylor

Level 3 Expert

6968 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenmore Washing Machines

  • Kenmore Washing Machines

Most Popular Question

get loud noise during spin cycle sounds

  • Washing Machines
Loading...