20 Most Recent Kenmore 24032\24036 Top Load Washer Questions & Answers


Agitate/Spin Issues (again)

if your coupler is good change your agitator dogs that will fix slow wash and clutch on top of transmission or lid switch for no spin
12/25/2023 3:57:56 PM • Kenmore... • Answered on Dec 25, 2023

Kenmore Series 80 washer. Agitates too slow

check the dogs in the agitator take off the cap it should rachett if it turns free replace the dogs in the agitator
6/4/2023 10:03:42 AM • Kenmore... • Answered on Jun 04, 2023

Washer fills slow only in the rinse cycle

I had the same problem with my Kenmore Model 11022956102 washer and first thought that it was the water inlet valves. So I replaced them, but found the problem continued. After about 25 seconds into the rinse cycle the water only trickled in. Checking with a voltage meter I found that I lost 120V at terminals 3 & 5 on the washer temperature controller after 25 seconds. Even though the wiring diagram doesn't show the water temperature control board, since it's full of resisters and capacitors, I figured it was the most likely problem. So I ordered a remanufactured board from Parts Simple (#3407125), received and installed it. The 17 year old washer is now working fine once again. I hope this helps someone with the same problem. /s/ Paul

8/23/2022 11:24:48 AM • Kenmore... • Answered on Aug 23, 2022

My kenmore washing machine vibrates

Might be a spring has come loose:
This video shows how to get into the machine and the location of those springs.

If your skate plate is out of alignment with the base it can vibrate alot also or your damper pads are worn can cause the vibrations

How it works: Direct drive

Manuals and more repair photos are HERE

themobilian_1218.jpg If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61
8/15/2022 3:35:11 PM • Kenmore... • Answered on Aug 15, 2022

Kenmore 800 series starts to agitate before reaching correct water level, also while filling up with water it pumps some out but will eventually fill and wash through the cycle. It appears to not be s

Clutch needs to be replaced that is why it is not spinning out. There is a clear rubber hose that goes from the fill valve on the top left of the machine down towards the bottom of the tub on the right side under the cabinet. Check and see if that hose has a hole in it of possibly came loose on either end. If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a
7/18/2022 2:22:52 PM • Kenmore... • Answered on Jul 18, 2022

Machine fills and agitates, but won't drain

Please empty your machine and run the machine empty. If the washer goes through the whole cycle without any clothes. Please let me know
9/11/2021 5:34:10 AM • Kenmore... • Answered on Sep 11, 2021

Kenmore washing machine fills with water then stops

turn the motor to see if it moves it sound like the motor
11/9/2020 11:37:42 PM • Kenmore... • Answered on Nov 09, 2020

Won't complete cycle, stops at rinse. and can't get hot water.

Are you on well water? turn off the cold water to the washer and clean the screen filter out. do not leave filter out.
the machine probably has a cold only final rinse so it won't work properly.
10/14/2020 6:29:56 AM • Kenmore... • Answered on Oct 14, 2020

Kenmore 80 series makes noise in sping cycle

Its the transmission. Try to find a used appliance store in your town. Most save used parts and you should be able to pick up a used tranny for around 100 bucks.
8/29/2019 11:02:06 AM • Kenmore... • Answered on Aug 29, 2019

Baby clothes under the ringer

Loosening top plastic nut and removed top 1/2 of agitator, then loosened nut to lift out bottom 1/2 of agitator.
6/27/2019 3:47:39 PM • Kenmore... • Answered on Jun 27, 2019

Dont drain


This issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. First make sure that the drain is not clogged and remove clogs if present. If no visible lint is present then remove the lower front access panel to check the drain filter and drain pump for any clogs, you'll need to clean the drain filter and drain pump completely. Hope this helps... Please post back for any further assistance.

11/9/2018 8:29:08 PM • Kenmore... • Answered on Nov 09, 2018

Indesit washing machine

Indesit Washing Machine lWB5113 Flashing Lights(Faulty ...

? 3:34 www.youtube.com/watch?v=-lnfePzPwTQ
Jul 29, 2012 - Uploaded by porracaralho caralho Indesit Washing Machine lWB5113 Flashing Lights(Faulty).mp4 .... older model- stopped in rinse cycle/flashing power and rapid wash lights- ...

How to repair Indesit washing machine that is Flashing ...

? 0:43 www.youtube.com/watch?v=Q9Yq2Cz8UFE
Jun 26, 2011 - Uploaded by XR600RQJ Washing machine Indesit starts to flash for longer and longer ...How do you unlock the door when the power is off?? every time i turn it ... My washing maschine ( Indesit WITXL 129 ) had the same problem - 6 from 9 LED lights ..
9/7/2018 3:06:24 PM • Kenmore... • Answered on Sep 07, 2018

Kenmore 80 Series dryer Model 11066862500 installation manual

Hello, this is Ava with Think Crucial. You may find the User's Manual for your Kenmore model by clicking the link below. https://www.searspartsdirect.com/partsdirect/user-manuals/11066862500-Kenmore-Parts-DRYER-manual You can purchase a wide variety of high quality appliances replacement parts direct from Think Crucial with free shipping and an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10 https://www.thinkcrucial.com/collections/appliances I hope this was helpful. Ava B. Think Crucial Customer Care http://www.thinkcrucial.com/
4/27/2018 11:01:26 PM • Kenmore... • Answered on Apr 27, 2018

Washer fills, but not agitating or draining

If the lid switch is faulty, or incorrectly adjusted, the drive motor is prevented from running. You do not say whether your repair man replaced the switch or the mechanism, but draining and spinning will only happen when the lid switch is engaged.
3/2/2018 6:06:26 PM • Kenmore... • Answered on Mar 02, 2018

My kenmore washer model 110.27802690

Under the lid there should be a small hole with a push down flap and that should be the automatic stop, which can either be a bad switch under the top of the machine or could be a broken trip/ prong on the lid that pushes this button when the lid is dropped. When the machine reaches it's spin cycle time leave it turned on and raise the lid push down on this flap with something careful to keep hands out of the washers tub and see if it works then!
3/2/2018 5:50:59 PM • Kenmore... • Answered on Mar 02, 2018

Kenmore laundry unit washer not draining during spin cycle

Fixya needs a model # for us to help. Thanks
1/31/2018 3:35:19 PM • Kenmore... • Answered on Jan 31, 2018

I have a Kenmore series

Just clean the filters off bluffs or coins and if not check the pump.
1/10/2018 5:46:15 AM • Kenmore... • Answered on Jan 10, 2018

Washing m/c wont start after finishing cycle with no problem .

Turtle nob until it respnds. Sound out of time
12/26/2017 4:20:36 AM • Kenmore... • Answered on Dec 26, 2017
Not finding what you are looking for?

3,909 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts


Level 2 Expert

171 Answers

Cindy Wells

Level 3 Expert

6688 Answers


Level 3 Expert

2530 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenmore Washing Machines

  • Kenmore Washing Machines

Most Popular Question

drum will not spin in any mode pump

  • Washing Machines