20 Most Recent
Kenmore 64902 Electric Dryer - Page 2 Questions & Answers
The belt that rotates the drum broke. How do I
ALWAYS UNPLUG YOUR DRYER BEFORE ATTEMPTING TO DO ANY WORK ON IT.
If you have to check/replace/repair your drum motor,drum seals,belt,rollers, etc.
If replacing drum seals be sure to use a good grade of weather proof cement to hold the seal/s in place.
Note: This method works for most front loading machines.
Remove the electrical console that holds the timer switch, start switch, etc. from the top of the dryer. Be real careful not to knock any of the wires off of the timer switch or other electrical connections.
Remove the lint filter and the screws that hold the filter housing.
Then remove the top of the dryer.
Note: Some of the tops tilt backwards and do not have to be removed completly.
Remove the front of the machine, this will expose the belt and drum, remove the drum and belt and this will expose the drum rollers, idler arm bracket with pulley, and motor with pulley. Pay attention to the route of the belt, this will come in handy when you go to reinstall the belt and drum.
Sometimes the belt will slip off of the idler arm or motor causing the drum not to turn.
While you have the drum out, I would recommend that you lubricate the drum rollers at the shaft of the roller with a good grade of machine oil like 3 in One oil. This will save you a problem later with the rollers getting noisy, also check your drum rollers for flat spots, if they have flat spots on them this will cause a noise like a thumping type noise. You will need to replace the drum rollers if they have flat spots on them.
This is a FREE answer, Please rate me
My dryer heats but the
Hi,
If your
dryer is not drying like it once did or if you just have nottaken the time to give yourself a
clean dryer in a long time then youneed to do that. At least once a year the
dryer cleaning should takeplace.
Lint build up in the
dryer duct is one of the main causesfor your dryer to fail.
Here is the rest of this tip about
DryerMaintenanceheatman101
Dryer wont stay on after hitting the start button.
Hello. The motor switch may be faulty and may require a new motor. Less likely is the start switch itself but usually this is just a momentary switch which gives power to the motor, if the motor switch is bad it will just go off when you let go of the start button. Dryer motors are usually around $125 plus the labor to fix it, an hour minimum. If the dryer is older I would just replace the dryer as you can get a new simple one for $250 often. Fewer bells and whistles the better. Hope this helps. Good luck.
Dryer wont turn on, the light inside dryer stays
Hi- Sounds like your door switch has shorted out (it controls the light as well). You can get this part from SEARS and they are not too hard to replace, just be SURE the dryer is unplugged before you open it up. You just have to remove the top, depending on the model (you didn't provide the whole model number, should have 3 numbers followed by a period then the rest of the numbers). If you are unsure of fixing it yourself SEARS can send out a Tech. Hope this helps.
Dryer stops while cloths are still damp
Hi
If the dryer is not drying the clothes then you would need to check for the following things-
Electric Dryer---
1. Inspect the fuses and circuit breakers they may have burned out or tripped. Usually, dryer will still tumble but not create heat if a fuse or a circuit breaker is not working.
2. Check for the amp reading at 240 V, it should have reading of 24, 21 and 3 amp (approx.) for 2 lines and neutral respectively.
3. Heating element may have turned or the connection to the element might be loose. Sometimes a shorted circuit element will keep on blowing the fuse or circuit breaker.
4. Motor wiring shorting to ground.
Hope this helps...
Daniel
My dryer heats up for about 30 seconds then there
sounds like it's going off on a high limit switch. Check and make sure the exhaust flex hose is clear all the way to outside and make sure lint filter is clean. If all is clean, you may have a bad limit switch.
How do you fix a door latch
You'll need to buy a replacement part.
The people at the shop can tell you how to remove the old one and replace it.
I own a GE #DVL223EB1WW
What do you mean by terminal block?
Where the wires are connected from the outlet?
Is this a 3 or 4 wire connection?
Thanks!!
The off/on pull switch appears to be broken. I
If your handy enough to attempt to replace the control timer yourself..You can start by unplugging the dryer first and removing the screws on the rear of the control panel...You'll then need to slide a flat screw driver under the clips located on the left and the right sides of the panel that attach to the top lid of the dryer... its a little tricky but you'll figure it out... once inside the control panel remove the nob from the timer and remove the wiring clip attached to the timer...remove all the screws holding the timer in place on the panel...A new timer could cost up to $85.00 it depend on the model...Good luck
Dryer runs but will not heat. Filter was very
It is probally one of the thermal fuses has blown. These are not resettable and must be replaced when tripped. They are inexpensive and easy to replace and test.
It could be several things the heating element , thermal cut out, thermal fuse. Most of these parts are very inexpensive and all are easy to replace. There is a video at www.appliancehelponline.com/servicemanual.html that can walk you thru the troubleshooting of your problem. It may be a different model but the troubleshooting will be the same. You can also get diagrams and illustrations of your specific model by entering your model #. Not all models are available. If you need help disassembling your machine there are videos of this also for most styles.
Kenmore dryer 90 series - problem starting -
sounds like your motor is going out for ur tumble tub either that or the belt is coming apart u cN Tke the back off and check the belt if it looks good u might want to think about pulling the motor and taking it to a motor shop and get another one usually thats gonna cost 90 to 150 dollars when u take it tell them to check that motor it sounds like the bearings are going out in the motor
Not finding what you are looking for?