Top 20 HP Photosmart Premium C309A All-In-One Printer Questions & Answers

Get the necessary software for your C309a here: https://support.hp.com/us-en/drivers/selfservice/hp-photosmart-premium-fax-all-in-one-printer-series-c309/3737192/model/3737193 Good luck.

Go to troubleshooting and scan try YouTube

https://www.Abctay.com is an online shop , We sell television and electrical accessories,all kinds of TV power supply board, logic board, TV LED screen, TV LCD screen, mobile phone screen, as well as various types of electronic tools,tv parts power supply,LCD,ccfl , LED,OLED,lcd panels,HMI,Inverter,LCD screen,lg screen,display screen,lcd monitor,lg lcd, lg monitor ,flat screen , touch screen,hmi,bulb,samsung, innolux ,Mitsubishi,philips, hitachi,auo,innolux,Planar, toshiba, siemens,chi mei,Weinview, Infineon,industrial LCD,industrial control, sharp monitor,vigor plc,delta, mitsubishi lcd,omron plc,etc.

Seems like the ink you are using is bad. It is thicker than what it is supposed be. If you are using HP ink, make sure it is not expired. If you are using a refilled ink or remanufactured ink cartridge, buy from someone else, not where you bought it last. You will need to clean printhead again. Also, to avoid this problem in future, the issue may be that there is too much ink gnk inside the printer. Where the printhead should sit on standby, the ink waste builds up. Clean that area with a butter knofe or plastic knofe. You may not have that issue of drying ink come back for a very long time. If you need further help, I’m available over the phone at https://www.6ya.com/expert/alex_22751bbefa74c3d0

no - enable snmp protocol in windows 8 https://www.loadtestingtool.com/blog/general/how-to-setup-snmp-monitoring-of-windows-system/ https://www.garlandtechnology.com/blog/enable-snmp-on-windows-8

http://www.pc4cracked.com/2017/07/winzip-pro-21-crack

So, why would that surprise you? Mac is much different than Windows!

This video will show how to remove a part to get to a stuck piece in your printer's ADF. Hope it helps: WP_20170601_002.mp4 http://www.303electronics.com/ If you need further help, I’m available over the phone at https://www.6ya.com/expert/alex_22751bbefa74c3d0

Either the carriage is jammed or there is a major electronic board failure. With the power disconnected, try to move the carriage back and forth with your hand. If it seems sticky, clean off the carriage rod and put a drop of light oil on it. Then work the carriage back and forth until it moves freely. Plug in and all should be well. If this does not help and you can't find any jammed paper or objects, you have a major failure and it will be cheapest to buy a new unit.

It could be a problem with settings or installation of your printer. We would suggest you to check on settings.

change the USB PORT

Disable all device power saving settings in Printer and also in system power settings,that's it.

Hi! I have an HP8610 printer that was having the same problem. What was causing the problem of disconnection was the wireless router being in one room and the printer was in another room further away. The signal was being weakened by having to travel through walls, various furniture, other electronic devices, etc. to get to the printer. Sometimes the signal from the service provider was stronger on some days than others. My solution was to remove any possible interference of the signal to the printer. I relocated the router closer to the printer, such that the signal didn't have to travel through 2-3 walls, and reduced any other obstacles. I also relocated the printer from the corner of the room, to a more open area to allow the signal easier access to the printer.
After I made these simple changes, I did not experience any further disconnections. I hope this helps you.

replace the cartridge.

There could be a paper jam in the printer head clearning system. If the head cleaning system is not completing the cleaning motion cycle the carriage will not move the catridge to the centre.

The picture shows the cleaning resovier. Each time the cartridge pass buy the print head is wiped and residue is deposited there. Looks messy and it is. As for the cartridge usage, they may be an economy selection in your software that may reduce ink consumption. Of course if you are printing in color versus black and white the consumption increases substantially.

Clean and change the ink absober.

Answer already been posted here :) Good luck failure oxc19a0041 how do fix it

Check with a multmeter if the input power (voltage) is sufficient. If ok, carefully open a printer check for dry joints over the in built power printed circuit board and if found resolder carefully. Sometimes rats penetrates and damage wires, find out and remedy.

Check antennae make sure is connected and is electrically & mechanically sound. Check the battery make sure is fully charged. Check the signal bar level, strong signal must be more than. 50%