20 Most Recent
DISH Network 721 DVR Remote Control - Page 8 Questions & Answers
The sat button on my remote is rapidly blinking, and now most of the other buttons will not work.
When the SAT button blinks repeatedly, or the buttons do a dance (Sat & DVD, TV & AUX, repeat) it means you need new batteries. Replace all four AAA batteries, ensure they are all four aligned the same way, and then hit SAT. Your remote should return to its normal function. If you leave the batteries out for too long, the remote will forget how to operate the TV and receiver, so be sure to have all four new batteries ready before you remove the old ones.
I have a Sony model KF-50WE610 tv. We moved it today and once it was set back up the picture is black and white. I have checked all connections, cables, and signal and nothing makes a difference. It
The cables connected are in the wrong spaces, either on the receiver or the television. Using component style cables, Green, Red, Blue for video, and White, Red for audio, one of the video cables is in the wrong spot. Using RCA type cables, Yellow for video, White, Red for audio, the Yellow is inserted into a green component somewhere. The ViP 722 is compatible with HDMI, which has a much higher resolution (1080p max with the ViP 722) and a better refresh rate (the ViP 722 max is 30Mhz), and as there is only one cable for both audio and video, is much easier to use, if your TV is compatible, you should look into using HDMI instead,
Program my dish net remote to my tv
Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily.
http://remotesearch.blogspot.com/
http://electronicshelponline.blogspot.com/
http://electrohelponline.blogspot.com/
Type in the brand name of your device, in the search box [at the top right] of the display window, and press enter to get all related posts. It will make surf easy.
Get my mute button to work
You must take apart the two halves of the remote .
Remove the rubber buttons bad (It usually is one piece)
Get a bottle of 99% iso alcohol at any pharmacy and let the whole rubber pad soak for 2 mins.
While it is soaking, take the end of a rubber pencil, and use it to clean the pc board by rubbing in circles on the printed resistor ink pads individually.
Remove the rubber button pad from the alcohol and dry well.
Take the pencil eraser and rub each individual black resistor ink with it.
Then dip a Q tip in the alcohol and do ALL of the resistor ink on both the pc board and the rubber pad.
Re assemble and there you have it!
Usually when you open the remote and pull the rubber all in one button key pad out, it will be sticky, so clean the button holes on the top piece of the remote (The Insides Individually) or the problem will continue.
The rubber keys will eventually return to rubber and the small black resistor ink on the opposite side will also wear in time.
I have seen this in the shop now for almost 30 years, and it is 95% the same every time!
I hope this will help!
My receiver remote 40.0 uhf 2g quit working. can I reprogram 6.o ir/uhf pro #132578 to replace it?
Check the remote control for its infra-red emission. Check it with fresh batteries. Check by pressing all the buttons on it; and see whether all of it generates infrared signal while pressing. If it is found OK, check and replace the infrared sensor inside the TV. If you wish to get some details; check the site linked here. It has details about how to check a remote control; by one among the post. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/ If the remote control is found OK; check and replace the infra-red sensor inside the TV. Contact any service technician
How to hook up Dish Network Receiver
which Dish Receiver do u have. if it is a Dual Tuner (322,625,622, 722) u run a RG6 Coax from the Dish to the back of the Receiver. on back of the receiver there should be two ports (Dish 1,, and Dish2) u will need two short pieces of coax and a Separator ,(which should have come with the Receiver. u hook the coax from the outside Dish to the single port of the Separator , now u run a coax (or RCA or what ever) to the TV. Turn on TV and Receiver.
on the Dish remote u hit the Menu button and hit #6 then #1 and #1 again (wait for each screen to change ) u should see a signal bar at the bottom. U will need to get someone to turn the dish a little at a time till u get a signal. once u get a strong signal u hit the Check Switch and let it program.
Why wont my 6.3 dish remote turn on 612 receiver
You can check out this link for directions on programming your remote: http://www.mydish.com/support/program-non-hopper-to-receiver. Let me know if you have any other questions!
Sarah J.
DISH Social Media Representative
Not finding what you are looking for?