20 Most Recent Kenmore 47702 / 47704 / 47709 Electric Single Oven - Page 3 Questions & Answers

Hello & Welcome to FixYa

Error code Sd indicates that the control is in demo mode and to exit this mode you have to press and hold the OVEN COOK TIMER and the START TIME buttons for around 20 seconds or till the time control begins to flash. Please get back to me with the model# if you have any other questions.

Kevin

Does the model number on your oven start with 790 (the three digit prefix)? If that is the case, then your oven was made by Frigidaire. The code F011 indicates a stuck key on the keypad. First make sure that nothing is pressing against any of the keys on the keypad. (The control board saw a signal from a key for 30+ seconds.) Press Stop to clear the display. Try turning off the power to the oven. Then check for loose or damaged wires between user interface control board and the touch panel. (Check the wires for continuity and the pins for corrosion.) Replace damaged wires. Make sure that the touch panel is properly aligned in the enclosure. There may be a spring or other part pressing on the touch panel. If the error persists, then replace the touch panel. Replace the user interface board if the code continues after replacing the touch panel. I hope this helps. See https://i.sears.com/s/d/pdf/mp-tc/10038420/prod_24762108912 for more information on a similar electronic oven control. Please add the model (including the prefix) of your oven, if you'd like a parts diagram/list. Cindy Wells

A Model # would help and you'll need it if you go to repairclinic.com or appliancepartspros.com where you can find help and parts. Best to you

question edited for clarity and add maker. Question moved to maker category. Stuck Button on panel or control board issue https://www.google.com/search?q=Kenmore+911.47609100+F0+error ..

Hi, you're correct about the control board being the issue. I would first get in-home assistance from home depot to help get the proper part number before making your order. And then you can order through kenmore. Thank you.

Hi, please press the "meat probe" (or button with term "probe" in it) button in order to turn that note off. Thank you.

What is the model number (including the prefix) for your Kenmore range? The prefix indicates the actual manufacturer of the range. None of the ranges that I am familiar with use P in any of the error codes. F5 indicates a problem with the control board (electronic oven control) for both Whirlpool and Frigidaire ranges. Most other ranges use 4 character error codes. I wish that I had better news for you. Cindy Wells

Here are the parts suppliers https://www.google.com/search?q=kenmore+electric+range+model+c970-440994+parts C970 Series schematics https://www.google.com/search?q=kenmore+c970+parts+schematic&rlz=1C1QJDB_enCA643CA644&sxsrf=APq-WBskB9Ws4--X0AfXux_wLfBVZb5Xyg:1643735081657&source=lnms&tbm=isch&sa=X&ved=2ahUKEwiq95Wt_t71AhWgJTQIHWnBAVoQ_AUoAnoECAEQBA&biw=1920&bih=937&dpr=1 .. ..

Sounds like a faulty thermostat. Google make model parts diagram

If it is giving an overheat alarm, I would have replaced the sensor anyway. If you have been using the self cleaning feature of the oven, it may be that, that burned the board. https://www.google.com/search?q=kenmore+convection+oven+f10+error ..

What is the exact model number of that unit and have you looked to see if there is a technicians sheet attached to the back of it?

Probably the pilot light feed is blocked. Clean the jets.

Due to the cost of control boards and the problems associated with them, I always advise a service call to replace them. In that way the part and the service provided is warrantied. They keep going until it is fixed. Request to send the board back as faulty and ask them to double check it is the correct board for your service and sub-model. There are 6 sub-models designated by another 4 numbers after the '9420'. https://www.searspartsdirect.com/model/1k9fnm0gf7-000582/kenmore-79094202310-parts ..

HI. follow the procedure below.

1. Disconnect power for at least 30 seconds.
2. Re-apply power and observe for at least one minute.
3. If code re-appears, replace control board (also called ERC or clock).

Almost certainly a burned out element, so test with a multimeter after turning off the power. Could also be; Burned out connectors onto the element. Fuse if it has them. Switch control. (unlikely)

buy new is only fix there is

Question edited for clarity. You need a service call. It's dangerous. The F10 code on a Kenmore oven means that the oven is overheating - the oven is detecting a temperature far over the safe range of operation. Most models also start beeping when this happens since it can be a safety concern.Apr. 14, 2020

How to Troubleshoot Error F10 on a Kenmore Stove ' Hunker

https://www.hunker.com > ... > Other Home Appliances About featured snippets

How To Fix Frigidaire Range F10 Error Code (appliancecodes.com)

When you got home, the meal was destroyed? The latent heat will stay in the oven cavity for many hours if properly insulated around the cavity.

KENMORE C970 USE & CARE MANUAL Pdf Download ' ManualsLib Kenmore Range Stove Oven Troubleshooting & Repair ' Repair Clinic