Answered Kenmore 79013 Stainless Steel Gas Kitchen Range Questions & Issues

LG oven Error Code F10

The F10 indicates that the electronic oven control board senses a runaway temperature condition in the oven through the oven sensor circuit.
This can be caused by a faulty oven temperature sensor probe or a failed electronic control board.
Oven temperature is detected by the control board as it monitors the resistance through the oven temperature sensor circuit.
You could have a failed oven temperature sensor, a wiring harness failure, an open thermal switch or a failed electronic oven control board that would cause this problem.
The first component to check would normally be the oven temperature sensor probe.
If you have a volt/ohm meter, you can shut off the breaker for the range and remove the screws that mount this sensor to the back wall of the oven.
Carefully pull the wire harness into the oven cavity until you get to the wire harness disconnect plug.
You should have enough slack to pull it this far into the oven.
Disconnect the sensor but do not let the wire harness retract back through the back wall of the oven or it will be hard to reconnect.
Measure the resistance of the oven temperature sensor with your volt/ohm meter. At room temperature, the resistance should measure around 1100 ohms.
The resistance chart is shown in the image below.

If the resistance is above 2200 ohms at room temperature, then the sensor probe is causing the F10 error code and will need to be replaced.

You can order a new sensor probe from the Sears PartsDirect website. The part number for the sensor is 316217002.

If the resistance is normal, then one of the other causes mentioned above is producing your F10 code.
You would need to access the electronic oven control board (Timer) in the console and check the resistance at the sensor circuit connection to the control board as the next step in troubleshooting this problem.

http://media.fotki.com/1_p,wbqdsfkrfqtswfqxgtqsskgwtqkq,vi/krdbrtqkgxkrbbqbrwb/1/1303472/5961857/image37801img-or.jpg

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
gt$$

Kenmore 79013... | Answered on Oct 01, 2010 | 1,021 views

1 Answer

I spilled between my oven windows on my Kenmore

It appears your ERC/CLOCK has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...

FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.

If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.

Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Kenmore 79013... | Answered on Oct 01, 2010 | 48 views

1 Answer

What should breaker size be for proper hook-up for

Hi,
Most ranges require a 50 amp breaker...if it is electric.
but most gas ranges can run off of a 20 amp circuit..

heatman101

Kenmore 79013... | Answered on Sep 30, 2010 | 76 views

3 Answers

Oven preheated but when I put the cookies in,

Hi,
check the control panel that whether it works properly or not..the heater...
hope this has helped you,,, Thanks,...

Kenmore 79013... | Answered on Sep 18, 2010 | 57 views

1 Answer

Clean oven burner

DeBruce Polish is Odorless, Non-Toxic and non abrasive and perfect on stainless steel, glass cook tops, polished granite marble and more. DeBruce Polish is Odorless, Non-Toxic and Non Abrasive. DeBruce is perfect on stainless steel, glass cook tops, polished granite marble and more. We buy DeBruce at debrucepolish.com.

Kenmore 79013... | Answered on Mar 05, 2010 | 124 views

1 Answer

F1 error Kenmore gas stove. Replaced module.

HI, This is a board fault code. The entire control board is damaged. Possible logic chip failure. This will require you to replace the entire board. this type of damage is not repairable.

F-1 - Board Failure(also called EOC or clock).

Kenmore 79013... | Answered on Dec 12, 2009 | 253 views

3 Answers

Oven door locks and un locks code F90

The F90 fault indicates that the maximum time allowed for oven door unlock was exceeded. The control attempted to unlock the door. The door lock motor or mechanism failed to unlock the door within the maximum amount of time it is allowed to be energized by the control board.

It is unlikely that you will be able to reset this fault code. You can try to completely disconnect electrical power and leave it off for 5 minutes. After reconnecting power, the fault code will probably reappear since the control will still detect that the oven door is locked. The only way to clear the fault code is to disassemble the range and repair or reset the oven door lock assembly. You will need a service technician to complete this repair.

Kenmore 79013... | Answered on Oct 10, 2010 | 8,102 views

1 Answer

Need a manual for Kenmore range model 790.71463703

The instructions said to screw down the valve at the back of the oven. We turned the valve down until it seemed to be seated, but the problem still persisted. So, against all reason, we hunkered down and put some muscle on the wrench ... ah, no cheater pipe, though. The valve turned slightly more than another full twist. That solved the problem.

I am a bit put out that someone at our house misplaced or lost the manual (if it's misplaced, is that lost?). But I am full-fledged pissed off that we have to pay to get support and that there is no online manual, or we have to write an email and then wait a day for a response. In the greed for ever greater exploitation of the consumer, businesses have sold their manuals to "manual.com" and the defenseless consumer must pay to join, pay for the manual, and ... O Lord, what other insults and invisible costs lay in wait for us ... and us so innocent!

However, that being said, I do appreciate your response this AM.

Kenmore 79013... | Answered on Jun 02, 2009 | 157 views

1 Answer

A Kenmore and GE gas range have recently been

New Ovens may give off an odor, but it will cease after a couple uses

Kenmore 79013... | Answered on Apr 24, 2009 | 228 views

2 Answers

Kenmore GAS Range The bake burner won't heat. The stovetop burners and broiler work. Service came and fixed it without replacing any parts. Problem returned. How was it fixed without using parts?

If it was me i would call the repair man up and ask what it was they did. He might say what he did . I am wondering if it was a burnt or loose wire that has come apart.

Kenmore Kitchen... | Answered on Jan 12, 2021 | 119 views

3 Answers