20 Most Recent Kenmore 46123 Stainless Steel Electric Kitchen Range Questions & Answers


the F3 error code is an oven temperature sensor fault. The sensor is a small probe that sticks out of the back of the oven wall. They do go bad and can be easily replaced. If I had your EXACT model number (found along the inside of the oven door or lower drawer) you can replace it.hope this helps

Kenmore 46123... | Answered on Jun 26, 2017


Press the clock button..... Does the time show (at least for a little bit)? If so, then you probably have the Energy Saver function turned on. Here's how to turn that function off (and have your clock display the time all the time): Press and hold the Clock button. Hold it for 15 seconds. Somewhere around 7 to 10 seconds, the clock will display, then go out, then come back on again. By 15 seonds, the clock display should be on, and if you then let go of the clock button, it should stay on.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

Kenmore 46123... | Answered on May 27, 2015


What is the model number for your oven? Kenmore oven are made by a variety of different manufacturers and depending on who made it will determine what the code might be.

Kenmore 46123... | Answered on May 13, 2015


In many ovens, the broil element is not used at all when baking. In others, it is on for only 5 or 10 second out of every minute when the oven is heating - which means that it will get warm, but will never glow red. Only when your are broiling will it glow red.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

Kenmore 46123... | Answered on Jan 03, 2015


What you need to do is press and hold the clock button for 12 to 15 seconds. When you first press this button, the display will appear. Then in about 7 or 8 seconds it will disappear. Keep holding it for 12 to 15 seconds until it re-appears. Now if you release the clock button, it should remain on.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

Kenmore 46123... | Answered on Jan 03, 2015


The cooling fan is controlled by the EOC and a temperature sensor located at the top of the oven near the control panel. If the temperature is above a 100 degrees there the cooling fan will continue to run. If it does not turn off when the temperature goes below this, there is a problem with either the EOC or temperature sensor. Try turning off the power to your oven for at least an hour to reset the EOC, this may fix the problem.

Kenmore 46123... | Answered on May 19, 2014


The cooling fan is controlled by the EOC and a temperature sensor located at the top of the oven near the control panel. If the temperature is above a 100 degrees there the cooling fan will continue to run. If it does not turn off when the temperature goes below this, there is a problem with either the EOC or temperature sensor. Try turning off the power to your oven for at least an hour to reset the EOC, this may fix the problem.
Regarding the shelves being 1/4 short, this is actually caused by your oven liner expanding not your shelves shrinking. The only fix for this is to have your oven liner replaced.
Both of these repairs are very expensive ( > $300) and may not be worth fixing.

Kenmore 46123... | Answered on May 19, 2014


I have experienced a f30 code on my oven...I was told to change the oven sensor probe which i did....The code still comes up!!! SEARS IS NOT ANY HELP

Kenmore 46123... | Answered on Jan 07, 2014


My kenmore glass top stainless steel slide in range has an error message code F93. I was attempting to allow my range to self clean when this err message appeared. Now I can't get the door unlocked. Help?? We've had a lot of problems with this range. We've had the service tech come out probably 4-5 times for different things. I think I got a lemon. It just turn a year old-we extended the warranty . I've called to complain but I got no help. They said it had to be for the same problem each time. Even the tech said the oven was a lemon but he couldn't help us. Any suggestions?

Kenmore 46123... | Answered on Aug 25, 2013


Hi,

To my understanding error code F1 would indicate a faulty control board, possibly thermistor control. The only recourse is to have this replaced.

This of course would require a fair familiarity of electrical/electronic components/circuitry and safety procedures, use of a DVM and possibly a soldering iron. It would be to your added advantage access to a service manual or at the very least a schematic diagram with voltage readings. Should you be uncomfortable performing a DIY (do-it-yourself), perhaps your best bet would then be to seek the services of a qualified professional.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Kenmore 46123... | Answered on Mar 20, 2013


What is the model number of your unit?

Kenmore 46123... | Answered on Feb 09, 2013


You had a power surge when the power came back on and it took out the control board. I see this all the time in the field and replace these boards. Here is the part you need to order.

Kenmore 46123... | Answered on Dec 07, 2012


please go to www.retrevo.com give your serial number, model, and mark and download.
God bless you

Kenmore 46123... | Answered on Jul 27, 2012


please see the next steps and proceed with common sense: God bless you
Door Latch/ Motor
The door latch may be stuck in a latched position or misaligned in this case just readjust the latch. In the case of a self cleaning oven that got stuck the motor or switch that controls the latch has failed. You will need to acess the motor. On some this is on the back, remove the back panel and you will see the small motor with a actuator rod attached to this. The first thing to try is to plug the oven in and with a rubber handle screwdriver push the microswitch tab down to activate the switch. If this does not get it working unplug and check switches for continuity. Check the motor for continuity. If you seee any burn marks on the motor or wiring replace the motor.

Main Control
First try to reset the control by unplugging or shutting off the breaker for 5 minutes. If this does not clear it check the motor and switches listed above. If all above is good the control has failed and will need to be replaced.
7_27_2012_4_22_15_pm.gif

Kenmore 46123... | Answered on Jul 27, 2012

Not finding what you are looking for?
Kenmore 46123 Stainless Steel Electric Kitchen Range Logo

112 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Kitchen Ranges Experts

Cindy Wells

Level 3 Expert

6074 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Paul Carew

Level 3 Expert

3492 Answers

Are you a Kenmore Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenmore Kitchen Ranges

  • Kenmore Kitchen Ranges

Most Popular Question

just got new ceramic top

  • Kitchen Ranges
Loading...